Search results

http://cgi.ebay.com/ws/eBayISAPI.dll?ViewI...AMESE%3AIT&rd=1 Finally got it from shipping. came across the water well.. Beryl

The Navy has given me a busy schedule and my boat is just sitting with all the other items. 45 in Dumas Deep Vee with stand, not to sure of the condition it is still awaiting pick up from the movers that shipped it from Turkey. The hull had been sanded and repainted from the Mercedes dealer in...

Installed an inline needle valve, and have the spitting of fuel out the tailpipe under control. But the darn thing still won't run when you remove the glow starter. I have installed three new glow plugs and still same thing. Then after a few runs in the stand, the engine is now getting warm...

If someone has one they want to part with, seems I always miss these on ebay, for the time difference is a bummer. Calculate shipping to: SKCS OConnor PSC 88 Box 2517 APO AE 09821 USA Military APO box in NY. Thanks,

Howdy I bought a roll from a fellow on ebay, I have about 20 ft left if someone needs a few feet let me know I can cut it and send out to ya USPS. I bought it to 1) black hose looks cool in yellow boat and 2) the line I had for water cooling was rubbing on the head and looked to have mushed a...

Well, heck the OPS 90 runs like a charm as long as you leave the glow plug starter attached... So how long does it have to stay there before I can remove it? I have it running in the stand, waiting for the head to get warm to the touch before I start the water to cool it, but it never gets...

Getting ready to PSC home and want to ensure the boat will be good to go when it finally arrived back home, good ole Texas for a month then off to Norfolk. Engine preps, hull or shaft requirements. I have to much time and effort in this to have if be stuck and not running when it arrives...

Well the never ending saga of what to do next.... I have an OPS 90 in a deep vee that is a booger to start. The clamp that I have on the exhaust boot is in the way of starting the engine. I can move it very little to make it so the belt doesn't rub the clamp, but when it is a one person...

You know when you attempt to have your cart ahead of the horse, and then the cart tips over? Purchased a carb that I don't require. Arrived last week, new wrapped in bubble wrap, unwrapped looked at, and wrapped it back up. Cost was $78.00, make an offer, or will swap for a HD steering servo...

With this set up I have a 4-40 rod, but it falls a little short on reaching the carb so I have two rods together. Holding them together in two places are collars, with allen screws in the center. Tighten the screws and the rods stay together. Is this the norm? It is what came on the old set...

Ok, got it running palced in the water, and went to turn and it kick a little and the went back to straight, found out a little about fluid dynamics. I was using the servos that came with the receiver, and they were, 3003 (go ahead and laugh), finding with any forward movement with the boat it...

I got the pics to load on the photo gallery (skcs gallery, boat building 101). I had to make them smaller, my bust ,need to read the directions on the page. Still not happy with the throttle link setup, but it will have to do.... Looking for some type of spanner wrench so I can tighten the...

Well, I didn't have time to place it in the water, but I am noticing things I dont like, the long throw from the servo to the carb is a bit much. Would anyone have a source for a cable assy that would maybe work better? Also a longer servo arm, the ones that came with the servos aren't long...

Well the finishing touches are about to be placed in, water lines for the cooling and the fuel preasure line from the exhaust. Gonna attempt to fire this thing up on Sunday and hope it doesn't head straight on to sea. Anybody got any oh, by the way for this newbie to look into prior to...

Any "lessons learned" that any one would like to pass on for the installation of 1/4 shaft tube? Boat design: 45" Dumas Deep vee OPS 90 nitro engine surface drive setup (Marine Spec) !/4 flex shaft (square head) Thanks Beryl

Hey, for all of you that have sent me parts and given me some GREAT pointers, thanks !!!!! I have finally received all of my parts and putting together.... It looks great... Again,,, Thanks,,,

Ok, for those tht had a helping hand with theirs or have been doing this for years, I aplogize for insulting your smart. But I want to complete this installation correct the first time. For placeing in the new stuffing tube and glassing it in. Any pointers or lessons learned on this, so...

When I received this old project the parts were not in place. I assume the tank will be placed ahead of the engine, which will place it about 1" fromthe carb. The line from the exgaust goes in one tube and then to the carb with the other. But what height should the tank be placed? is it...

Yes, new to this. I finally got all my parts and putting this project together, and want to do this right the first time. How does this carb work? I am use to gasoline and this one is differnet. Explain set up and how the throttle works and ect. Also the fuel I have is 25% is that correct...

Well for those of us that are over 3500 miles from a Home Depot and Lowes... I found this guy who has a website and all the neat things.... for boat stands. [email protected] www.tdrevelus.com Just some info.