Search results

I finally finished my build. I was supposed to start testing today but the weather did not cooperate. Its set up for 6s. If it turns out to be too much weight i will have to try as 4s.

I am finally finishing up my FF.45. It will be a fast electric boat. I could really use some help with the turn fin location, cog and any other set up tips for this boat. Thanks

I have a 7.5 power head. Its just a standard 7.5. It came on a boat I picked up and I am keeping the lower unit for a fe conversion. It is a running motor with good compression and the bearings feel smooth when I turn it over. Asking 50.00 plus shipping.

Had my ts3 out today. Its set up for 6s with a 3659 1900kv motor and a tfl442 prop. Im testing on a pond that isnt quite big enough for a good long run and using old batteries that are not up to the task. I was still able to manage 50mph though. needs a wee bit more tweeking but with better...

Im on the market for a new tunnel. I cant afford any of the higher end hulls so my choice would pretty much be between the vs1 or the ts3. It will be set up for FE and used only for sport running. I would like to hear some views on which would be the better choice. Im kinda leaning toward the...

I am building a .45 FF rigger. 6s. castle 1717 motor plus a rather large 280a esc. Im starting to get concerned about the weight cause I know this hull was designed for nitro. Is there any changes I need to make to the boat for this fe setup?. Im pretty much at the point where it would have to...

I'm running a sf 200a esc (non data logging) with a t600 outrunner. I am having issues with the throttle. There is a delay both on the throttle and off. It takes a second or two for the throttle to totally kick in then it takes time to stop spinning the motor after I let off. I have not used any...

I am trying to calibrate my data logger to use for hi amp readings. I hooked it up in my boat and ran it on the bench for a couple minutes. I used a clamp on meter to get an amp reading but the reading on the meter fluctuates so much its impossible to get a true reading. Is there a way to get a...

Ok yesterday I had an issue with my kneeler. Launched it and lost radio control. I was using the flysky 3ch radio with a swordfish 200a esc. Today after the esc had been thoroughly dried out i tested it. When hooked up to the flysky radio the esc started playing a bunch of tunes which tells me...

Today turned out to be a one of those days my mother warned me about. Went out to enjoy a day of running boats only to have one disaster after another. First I launched my kneeler. It was going fine for a couple seconds and then I lost radio contact. It raced toward the other side of the river...

I am toying with getting a t600 for my wildthing mono. I'm concerned about the volume of air in a hull that size. Will it be enough to keep the outrunner cool or is it going to get too hot??

Skip past the first 30sec where I was adjusting my radio...lol. Other than an issue with weeds at one end of the pond causing it to spin, it is working very well. very stable design.

I am building a fe version of the ff.45. I will be using a CC 1717 motor which is a beast, so i will be using a 1/4 flex shaft. I need some suggestions on prop size so i know if I should use 1/4 prop shaft or step it down to 3/16.

I am looking for help with a rigger build. I want to build a .21 or .45 size rigger for FE. I cant do anymore scratch builds because of bad wrists so im hoping to find someone willing to share the files needed for lazer cutting, or a source for someone who does a lazer cut rigger. I have seen...

Has anyone ever had a paper to cad conversion done. I was wondering if it would be expensive to have done.

I am building an Fe hotshot .45 tunnel. It is the FG version and has a block inside the sponson for a turn fin. My question is should I use it. It seems that none of the tunnels I see have turn fins anymore.

I plan to build a kneeler over the winter . My question is what makes a kneeler hydro different (in design) from a regular hydro. Since im going to be making one Im wondering if it would be worth while doing two and converting one to an inboard, sport hydro style. But i have no idea if those...

My wildthing mono was running too loose so I added trim via trim tabs. It has the hull running much better but im wondering since the angle of the hull on the water has changed so has the angle of the prop. It is set straight out. Should I adjust it down to compensate for the change in the hulls...