Search results

Anyone have pistons for CMB 91RS for sale? Where to bay, any other maker/brand that that fit? Know that piston/sleeves normally sell together.

I'm looking for the hing part (bearing block), between rudder and bracket for a 21 mono rudder. Se picture. Also looking for a large dual intake staggerd rudder blade, for a gas mono. Thanks, Rickard

Looking for a complete or top end 7,5 eng for my Leecraft. Rickard

I'm looking for a dual intake rudder blade for Seaducer mono hardware, Tidewater. Thanks Rickard

Have any one bin using these props (M and P), the M serie is a low lift (I think) and the P serie I do not know anything about. What mods do these props need to work, do you pitch/cup or cut them like a 1400, 1600 or X serie prop? Thanks Rickard

This is what it looks like after a major rebuild. This was an old Seaducer 44 that was cut apart and then rebuild,,, now it's 50" long and wider then before. All that to test some new things, among other, a complete new bottom, new and higher nose. In total, some new aero and hydrodynamic...

Have a NIB CMB 45 VAC with extra drum for direct drive/gear drive, parts as in the pics. No time for it therefore want to trade for a CMB 91 eng,,,,, If no trade might sell it! I will pay for shipping cost from Sweden to US. For you, I have a US adress. Thanks Rickard

I'm looking for a flow meter, for 45 - 90 eng. Thanks Rickard

Looking to bay props that is for the Seaducer gas mono, maby two blade. I know there a lot of "nitro" people here but some of you mitght have some props that fit the Seaducer mono. If not I will contact Mr Seaducer ........:-) Rickard

Here some pics!!! Rickard

I know there is many of you here on IW that have a "black belt" in the Seaducer's! I have a quiss for you, about were the CG should be, in distance from transom (for a Seaducer 44" SD3 with a 91 eng). I know about the setup on the Seaducer web site but there is nothing about were the CG is...

This boat is build for the NAVIGA O-7.5 class. We race 8min heats on oval corse. Therefore the boat has got 3 fuel tanks, 2 center and 1 front (24oz) tank and 1 float chamber. The boat get stuffed with fuel lines!!!!!!! Very high payload at the start of the heat. I was introducerd by David...

I'm looking for a CalCraft 44", open to all offers, nitro, gas or hull only,,,,,any combos,, Thanks Rickard

Hello people, Here in the north part of Sweden the summer is over, so If I'm not Jesus the winter is here cause one can now walk on the water. I've been lucky to have a parner in crime regarding the boat hobby that is working at a university. Where there are resources!!!!!!!!!! The picture...

As the title say, looking for a Seaducer 44". Thanks, Rickard A

Hi there, My own X-Craft mono is complete and ready for the first tests. This one is build for the NAVIGA offshore O-15 class. We run on oval corse for 8 min heats. Thanks to David Wilfong for the tuned engine, and it's mounted to a gearbox. No one yet have tested geard engine's in this class...

Here in Europe we race in rough water for 8-12min heats (25-30 laps), therfore a need for bigger boats. Big boats tend to run faster with big prop's. To do that you can gear it to be able to swing bigger prop's. I messure my boats performance in "lap time's", second to that and in some way the...

As the title say, looking for Octura X452/2 and X470/3, X572/3. B/S if possible. Thanks, Rickard

Looking for a CMB 45 Nitro AB pipe and header. Thanks, Rickard

WTB digital servos, typ Hitec 5245 or 5085. Thanks, Rickard