Search results

Hello Guys, It's been a long time since I've been on this forum. I recently decided to dust off my riggers and decided to finish my twin VAC 91 all carbon Crapshooter. I sold my Carbon Crapshooter 45 so I have my new CMB 45 spare engine FOR SALE along with all my 45 pipes. If you look at each...

Hello Guys, I am selling my sons Seaducer 90 which was built by Jerry just just before I stopped racing. It has a VAC 91 that was run at one race and never really even broken in. We ran it in three heats rich and never got to setting it up and trimmed out. The engine was flooded with Marvel...

Hey guys, Any of you tested the two pipes from All Hobbs? He sent me pictures of the Parabolic pipe and the Rossi 80/90 pipe. Albert

Hello Guys, I previously posted looking for the old Rossi 80/90 pipes but would also like to add the Steve Muck 15cc pipes also. So if any of you have either of these pipes I will need a total of four piped. I am building a new twin VAC 91 Crapshooter to further intimidate and annihilate the...

Looking for the old Rossi 80/90 pipes and Steve Muck 15cc pipes. Thanks, Albert 786-280-1246

If any of you guys have any of the Rossi 80/90 pipes that you are willing to sell then give me a call. Thanks, Albert 786-280-1246

I have two starters for sale. One is a Borris starter with the 4 cell lipo battery and the second is the 24 volt Sullivan with the machined purple handle and the custom 18 volt Makita pack. Borris starter is 4 cell gen and works awesome on any engine . Price is $100.00 including Lipo battery...

Ok David and Mark, My objective is to increase performance if at all possible and most of all to not worry any more about my bearings going bad due to residual moisture or nitro. I decided to start this new thread because the full comp thread did not address my issue clearly. I recently...

Im selling my JAE gas rigger RTR minus radio, the tub is 100% Carbon/Kevlar build, this boat was built like all my crapshooters, highly renforced and built to last a lifetime...the motor is a rear exaust J&G all billet 26cc by CC racing, final tuning by CP mod, i have aprox 1/2 gallon of gas...

what have you guys found out about removing the low speed needle from the stock carb?? is there really more top end and is it worth the sacrifice?? what if your ahead of the clock and need to slow down?? now you have a carb loading with fuel, and risk stalling the motor...has there been true...

IM SELLING MY QUICKDRAW REAR EXAUST HI REV RACE MOTOR, A BRAND NEW PISTON AND SLEEVE AND NEW BEARINGS ARE IN THIS MOTOR INSTALLED BY QUICKDRAW, SINCE THEN THERE IS ZERO RUN TIME..I PAID $1500 FOR THIS NEW, IM ALSO INCLUDING SEVERAL IGNITION COILS AND A HEADER TAKE IT ALL FOR $695 O.B.O...

OK Guys, Someone has to have an Orlic Jewel balancer they are not using and want to turn it into cash. Email me at [email protected] Thanks, Albert

I am looking for an Orlic jewel balancer and I am willing to pay $250. If interesed in selling one email me at [email protected], Thanks, Albert

Willing to pay $250 for an as new Frank Orlic jewel balancer. Respond here or email me at [email protected]. Thanks, Albert

Hey guys, I am looking for a Frank Orlic Jewel balancer and I'm willing to pay $250 in order to avoid making one. Email me at [email protected] or resond here. Thanks, Albert

Hello Guys, I am looking for an Orlic Jewel balancer in good shape and willing to pay top dollar. PM me or email me at [email protected] Thanks, Albert

Hey Guys, I just got a 44" Seaducer for my son. I went with the VAC 91 and want to know what is the best prop you guys have tried on this set up. Boat comes with an X467. It runs OK but after running my Crapshooter riggers it seems slow. The engine does not seem to turn up that high. Love my...

Hello guys, I am selling a JAE gas rigger I built using carbon and kevlar. I purchased an original kit and duplicated the center section using composite. I powered the boat with a rear exhaust J&G 260. This boat has some battle scars that have been repaired and only need paint. The boat is...

I am sure this question has come up before but what is the best finish to put on a prop in order to get the best performance? 1) Polish 2) Sanding disk swirls 3) Light bead or grit blast

I am looking for a Frank Orlic prop balancer. Please contact me through IW pr private email at [email protected] Thanks