Search results

Due to increased work commitments, and no time to finish..I am hoping to sell this 1/10th scale Dumas Drop sponson, Shovelnose hull. It was run as a brushless hull. Rebuild is about 85% finished. It needs the top to be skinned back on and motor of your choice, whether nitro or brushless...

Hello. Does anyone have a quick dimension they could post. of the .21 sized front sponsons. I am building a scratch .21 rigger and have a shape in mind that I like, (really love the crapshooter or hummingbird sponson shape) but am not sure where to start. I am looking for sponson bottom length...

Hello, for a winter project..I would like to use an old hull, primed and smooth, to act as a fiberglass mold (that I can remove the hull and not ruin it in the process). I've been doing a lot of research about fiberglass molds and release etc. In a nut shell, I will be tracing the hull...

-------------------------------------------------------------------------------- To all of you who run hand built shovelnose/pickleforks based on Garry Finlay 1/10th plans...as well as the few Dumas 1/10th scale hulls.....what sort of speeds are you getting with these "stock off the plans"...

Here is another hull I am parting with, to thin things out. This is a brushless Keps .21 hull I finished recently. perfect for 4s, and neu/feigao power. I have also had great luck with this hull using scorpion outrunners. Hull is undrilled, so mount any hardware you want, stuffing box is...

I am having to part with my whiplash sport 20, hull and vacu cowl. I built this precisely and the finish is fantastic. It comes with motor mount, for feigao/neu motor. Stuffing box glassed in, turn fin included with its hardware. No running hardware or electronics. I am having to thin my herd so...

I am willing to trade my brushless converted Mugen Mbx5-r buggy for a clean sport 20 or sport 40 hydro. The buggy comes with brushless Feigao 10xl motor mounted with steel pinion gear and steering servo mounted. Does not come with rx/tx or esc. I have an extra set of wheels (8 wheels total, 1 is...

I am in the process of finishing up some epoxy and cloth work on my H&M sport .21 and was wondering what is the best way to prep for paint? Do I need to sand down to bare fiberglass or just smooth out the gel coat and break the first layer of gloss? Any thoughts would be great. This is my FIRST...

http://www3.towerhobbies.com/cgi-bin/wti00...=LXWPW0&P=7 I came across this today at towerhobbies. Available late May.....anyone hear about this radio system yet? 2 channel, and very affordable...but 2.4ghz. could it be worth the money? I know it is not available yet, but maybe someone behind...

I have been working on this rigger hull, for quite some time now, along with my whiplash, and starting on a miss vegas 6s conversion, some chopping, glassing etc. This hull is nearly complete, just need about 2 coats of clear on the sponsons then it is ready to hit the water. Hull design is...

I am finishing a rigger that is (34" from sponson tip to drive dog) it is a 6s brushless hull with 11xl feigao, and .187 flex. I have it almost ready to go. One or two more shot of clear on the sponsons then its to the water! my question is, what is the maximum gap between flex coupler (coupler...

I am looking to trade 2 props an m447 and x440, I am looking for y537, and a x637 to test on my rigger and whip. both props are deburred, and have a quick once over, balance on them. Looking to trade, or ? Thank you Patrick

I am curious what motormount/drive shaft angles (if any) you are running on various boats, hydro, mono, rigger etc using flex shafts. I have tried both flat (horizontal) mounted, with a slight bend, as it comes to the coupler, then a bend below where it exits the hull basically an s-bend as the...

I am finishing a few rigger hulls, and would like to know where you all order your carbon/fiberglass tubing from? particularly I am looking for .3125 (5/16) inner diameter tubing that will fit over the 5/16 aluminum stubs I have glued into my sponsons. I found a site that sells cheap fiberglass...

I am almost to the point of paint, on my whip 20 and a few riggers...I would like to try a fade paint job with 2 colors. say, yellow to black etc. you ge the picture. My question is, however...what is the best way to do this...with a rattle can. Some have mentioned, use a piece of paper as a...

http://cgi.ebay.com/28-shovel-nose-hydro-f...1QQcmdZViewItem I have seen these shovelnose hydros on ebay for a while now... has anyone run one, either nitro or brushless.....any input let me know. It seems like the kind of boat that could be bought on the cheap and with a little glass work...

I have been building boats for about 1.5 years now. I always use west system on the inside of the hull to seal, strengthen etc as many of us builders do. However on one of my most recent rigger builds, I decided to seal the bottom of the sponsons with west system to then sand etc and made a...

Hello, I have a freshly built custom rigger that I would like to trade for a 1/8th scale buggy/truggy/car roller only. I would like a nitro roller to convert to brushless. This rigger is designed for a brushless motor setup. 6s lipo and motor mount is installed. I am just sealing the outside...

Merry christmas to all of you....wishing a great holiday and new year to you all. I have learned soo much from this online boating community and appreciate all of the shared knowledge.

I am once again looking for a brushless motor, either a feigao/nemesis 10-11xl or a neu 1521. I would prefer a new motor, over a used one but let me know what you have. My last deal fell through, which is why I am reposting this message. Thanks. pm me if you have anything for sale in my specs.