Search results

Dad is looking for a 26cc or larger plus pipe for a large v hull, zny help is appreciated. Brandon.

Its time!!, nitro prices are insane, and cant stand to see my cat on the shelf, looking for electric options for a aeromarine cat conversion, want fast and runtime, boat will not be raced, looking for best budget motor /esc, but its gotta be fast. can anyone help?

just purchased a old NIB p45 and need a manifold (water cooled if possible) for a mono hull, can pay with PayPal, Thanks , Brandon.

Took my new .21 beta evo appart last night to inspect it before installation into my JAE rigger and , tried to reassemble it but i cant seem to get the rod over the crank journal, just not enough clearance to get the rod parallel the crank pin, ive been sucessfully rebuilding buggy engines for...

looking to convert a dual brushed boat to dual brushless, i'll be using castle 540 size motors 2-1 gear reduction and 2)3cell lipos, looking for budget escs and the best way to wire dual escs. the boat is just for messin around and for retrieving nitros. Thanks in advance, Brandon.

Just completed a jae 21 and installed a broken in toro nero and it just doesnt come up in revs, this engine was insane in my truck but now is a real pooch (maybee 30 mph), the boat is not raced, reliability is most important, my current setup is.. 1. sullivan 8 oz (no clunk) 2. odonell 30% 3...

looking for a 15mm size, rotary carb for a novarossi .21 inboard with low speed needle intact WI/USA

Iv'e see a few people running car engines in boats and was wondering how? the threads on a "p" shaft engine are too short, i have heard that there are adaptors but have never seen them. i'm also in need of a cooling head and button (nova, 16.22 bore) Thanks in advance. Brandon

just picked a used cmb .65 and it turned out to be a dual plug engine, just wondering what the starting proceedure is for an engine with two plugs and any problems/benifits associated with them, also the low speed needle has beed removed and sealed, how will this affect operation? any help is...

Dad's old cmb 4 bolt carb fell apart again (3rd time) and lost the entire low speed needle assembly, its a flat slide type. are there any carbs or parts out there? or any other options? any help is appreciated. Brando.

just picked up a replacement macs 1365 pipe for dad's rigger and was wondering if anyone can help with the length, engine is an O.S.65 disk rotor.

need a piston/sleeve set for a cmb .67hr green head, part # C91153, can anyone help?

wanted piston and sleeve for the newer style os .65 vrm drum type

dad and i run an older 4 bolt silver head cmb rigger that is kind of a pain to get going, but once it does, LOOK OUT. on the first run of this year it seemed ok for a bit then decided to take flight at part throttle twice. what could have changed to have caused a boat that used to be glued to...

dad blew up his os max .65vrm and now needs a piston and sleeve, can anyone help?

i found a great deal on a non pullstart os max rgm ($100) NIB and i want to install it into my m.v. has anyone done this?, any recomendations?. Thank's. Brandon.

where in the USA can i find a dealer for the new rb concept .21 marine engine, i think it's called the "c9". any help would be appreciated.

hello all, i'm running (not racing) an aeromarine sprint cat with a 67 green head, 67-80 fat pipe, x457 prop on 50% fuel and am only getting 3-1/2 minutes runtime on a 16oz tank of fuel. i'm wondering if this is normal. if so, is there anyway to increase runtime by swapping props or pipes? which...

picked up some 40 % byrons car fuel, (11% oil) and would like to run it in my 67 green head, can anyone give me an idea on how mutch oil to get close to 20% oil? i will be using klotz techniplate for nitro. when the bottle says 20% oil, is that actually 20% of the gallon or is it measured a...

looking for an os 21 inboard or some other reliable budget engine with a rotory carb.