Electric sport 20

Discussion in 'Fast Electric Forum' started by ACTION JACKSON, Jan 8, 2019.

intlwaters.com

Help Support intlwaters.com:

  1. Jan 8, 2019 #1

    ACTION JACKSON

    ACTION JACKSON

    ACTION JACKSON

    Well-Known Member

    Joined:
    May 10, 2007
    Messages:
    78
    I want to set up a 20 sport hydro electric and I'm looking for information. batteries motors props and speed controller. thanks for any help as well a bear hull weight suggestion also. 
     
  2. Jan 8, 2019 #2

    RaceMechaniX

    RaceMechaniX

    RaceMechaniX

    Well-Known Member

    Joined:
    Apr 27, 2007
    Messages:
    2,246
    Location:
    Asheville, North Carolina
    Steve,

    Easy to make a recommendation, but first a couple of questions:

    Do you plan on racing within either NAMBA or IMPBA?  If yes, which one or both?

    Do you want a "limited" set-up or an open set-up?  Limited typically refers to a motor limit.  NAMBA and IMPBA use different rules here.  Limited motors are often the Aquacraft and Proboat 36mm motors.  Although both organizations are moving towards a diameter and length limit to open up the pool of available motors.

    If you prefer an open motor, do you want inexpensive system system, balance of cost and power or the absolute balls to wall crazy power system?

    A lot will also depend if you prefer building wood kits or semi finished fiberglass hulls.
     
  3. Jan 9, 2019 #3

    LohringMiller

    LohringMiller

    LohringMiller

    Well-Known Member

    Joined:
    Jan 25, 2017
    Messages:
    319
    Location:
    Eugene, OR
    I put together an Arno Brits (now Leecraft) sport 20 with an Neu 1515 1Y (2200 KV) motor and a Castle Phoenix Edge Lite 200 ESC with added water cooling.  I planned to run it on 2 4S 5000 mah packs in parallel.  At around 26,000 loaded prop rpm it should run standard  40 to 45 mm sport 20 props.  Check with Brian Buaas for better information on props.  That would fit the unlimited NAMBA or IMPBA P sport hydro classes.  Some day I'll find an excuse to actually race it.

    Lohring Miller
     
  4. Jan 11, 2019 #4

    ACTION JACKSON

    ACTION JACKSON

    ACTION JACKSON

    Well-Known Member

    Joined:
    May 10, 2007
    Messages:
    78
    Thanks for the info guys I do want to run unlimited and I also want to get at least 50 miles per hour out of the 20. I don't mind spending a bit of money if need be and I do prefer fiberglass over wood although I do see some nice wood kits out there but by the time you get done putting together ceiling sanding finishing and painting for me it would be better to use fiberglass Hull. For props in what area or number of prop size are we talkin about
     
  5. Jan 11, 2019 #5

    RaceMechaniX

    RaceMechaniX

    RaceMechaniX

    Well-Known Member

    Joined:
    Apr 27, 2007
    Messages:
    2,246
    Location:
    Asheville, North Carolina
    Steve,

    The two best glass hulls are the Phil Thomas Stealth and Insane FE30.  

    The PT Stealth is epoxy glass versus the Insane FE being gelcoat and polyester.  The Stealth does take a fair bit of pin hole filling and prep for paint, but I believe is a better hull.

    To achieve 50 mph, I would recommend the following for a power system:

    Motors:

    TP 4060 1950kv or a TP4050 2100/2350kv motor

    Castle 1515 1Y

    ESC:

    Swordfish X+220A or OSE Raider 150A if you use the TP4050 2100

    Batteries:  45-80C, 4S2P 8000-10000mAh total.  Many options here to choose from.

    Props:

    Octura X440/3, X447, X450, ABC 1716, 1814, 1914

    That will get you 50mph pretty easy with low stress on the power system.
     
  6. Jan 11, 2019 #6

    LohringMiller

    LohringMiller

    LohringMiller

    Well-Known Member

    Joined:
    Jan 25, 2017
    Messages:
    319
    Location:
    Eugene, OR
    I believe Ron Shaw is building the Leecraft sport 20. My hull was going to be a plug for the design.   Alfred Lanza had good luck with it as a nitro boat.  See



    Lohring Miller
     
  7. Jan 13, 2019 #7

    ACTION JACKSON

    ACTION JACKSON

    ACTION JACKSON

    Well-Known Member

    Joined:
    May 10, 2007
    Messages:
    78
    Thanks a bunch guys. I have looked at a few hulls from ml boatworks, Phill's boat & I see Ron is getting to put his new boat out. I also looked at the Blazer sport 20 & all are very good boats. Ron on your boat can you tell me how deep you sponson are.  I do need these questions answered so I can choose the boat for my needs. Thanks for all your help guys. 
     
  8. Jan 13, 2019 #8

    bzubee

    bzubee

    bzubee

    Well-Known Member

    Joined:
    Oct 17, 2002
    Messages:
    4,118
    Location:
    Huntsville, AL
    Steve OSE swap site has a Swordfish 220 for sale with everything you need for $160 good price.
     
  9. Jan 14, 2019 #9

    ACTION JACKSON

    ACTION JACKSON

    ACTION JACKSON

    Well-Known Member

    Joined:
    May 10, 2007
    Messages:
    78
    Hey Bill thanks I will check it out.good to hear you on here. 
     
  10. Jan 17, 2019 #10

    Don Ferrette

    Don Ferrette

    Don Ferrette

    Administrator Staff Member Admin Moderator

    Joined:
    Nov 26, 2003
    Messages:
    14,795
    Location:
    Mechanicsville, Virginia
    Steve I can tell you from first hand experience if you don't mind gluing some wood together the ML kits are the way to go. I built the 20 size in FE for my wife and I just finished a new nitro sport 40 for myself for the upcoming season that is ballistic. Brad Maglinger has been cleaning up with his ML nitro sport 20 as well for the last 2 seasons. Laser cutting is top notch and super easy to build, hardest part is waiting for epoxy to dry so you can keep going. Build it exactly like the directions tell you and  it's a winner. B)
     
  11. Jan 17, 2019 #11

    ACTION JACKSON

    ACTION JACKSON

    ACTION JACKSON

    Well-Known Member

    Joined:
    May 10, 2007
    Messages:
    78
    Thanks Don for your input. I know Brad well & watch his boats run really good. I'm still kicking it around & haven't decided yet. But I do appreciate your input. Thank you. 
     
  12. Feb 25, 2019 #12

    PiroSteel

    PiroSteel

    PiroSteel

    Active Member

    Joined:
    Jan 14, 2016
    Messages:
    42
    Location:
    Göd by Budapest
    I like this sponson design too
     
  13. Feb 25, 2019 #13

    Bradley Maglinger

    Bradley Maglinger

    Bradley Maglinger

    Well-Known Member

    Joined:
    Sep 24, 2012
    Messages:
    1,096
    Location:
    Owensboro, Ky
    You have many great hulls to choose from, MLboatworks, Phil Thomas, LeeCraft, Blazer sport 20 just making the decision is the toughest part.  
     

Share This Page



arrow_white