E
Edward
Guest
Hey guys,
Selling my baby...highly modified brushless conversion of the Aquacraft Miss Vegas RC boat. This was built and modeled after ProperChopper's on OSE and was GPS'd at 61.7MPH with my cell phone in a Ziploc bag...don't laugh!!
$350 + shipping NO TX / RX
It has never been crashed and has been a shelf queen for the past 2 years. And includes the following specs...
--NEU 1515y 2200kv brushless motor with watercooling jacket ($230+) less than 15 min run time
--Modified watercooled 200A ESC with upgraded 5.5 bullet connectors setup for 4S lipo configuration
--high torque servo
--hull has been water sealed and fibreglass layed for rigidity
--rear wing with all hardware is included but I found it harder to tape up with the rear wing
--extra BRAND NEW 200A ESC!!
--extra BRAND NEW 1800KV Brushless Outrunner motor...will get you to just shy of 50 mph...good for practice runs
--octura x642 prop polished, sharpened and balanced which will get you into the 50s...if you want me to swap in the M445 prop for over 60+mph just say so.
Also have a Brushless Deep Vee w/ hardware 2200KV 180amp ESC...and yes those are REAL 25 aught 6 Remington cartridges (one was drilled out for the purpose of the exit point for the water cooling) on the rear of the hull which have been fashioned to look like exhaust pipes!!
$250 + shipping NO TX / RX
Its got a few spider cracks on the top of the hull but its never been crashed and I've repaired them so the hull is very sound. Its sat on my shelf for the past 2 years and has the following specs:
--2 x RARE Turnigy H3126 2200KV 1500 watts outrunner watercooling (1 installed w/ 20min run time, 1 brand new)
--180amp Turnigy Pro Brushless ESC with upgraded 5.5 bullet connectors setup for 4S lipo configuration
--extra brand new 60amp Turnigy Pro Brushless ESC
--high torque Traxxas waterproof servo
--hull has been water sealed and fibreglass layed for rigidity
--octura x642 polished, sharpened and balanced which will get you into the low 50s.
I can sell everything for $550+ shipping with the following...
--Both brushless boat rigs with brushless motors, ESCs installed, waterproof RX so both Ready-to-Run
--Boat stands for transportation
--2.4 Traxxas TX / Waterproofed RX
--4 rolls of clear hockey tape to secure the boat hatches
--Rear spoiler wing for Hydroplane with hardware for you to install if you'd like...I didn't like it installed because it always got in the way of taping down the hatch
--Grim Racer grease for main drive shafts
--A tonne of bullet connectors for your lipos to hook up the ESCs
--Brand new Turnigy 130A power analyzer
--Extra brand new water cooling motor mount for the Deep Vee Mono
--Extra silicone tubing for watercooling purposes
--Extra brand new Turnigy 3126 brushless outrunner 2200KV 1500 WATTS!! (the other is installed in the Deep Vee Mono) This motor is super RARE and the guys on OSE have already been messaging me to part it out!
--Extra brand new Turnigy 1800KV brushless outrunner
--Extra brand new watercooled 200A ESC
--Extra brand new watercooled 60A ESC
--All of my props....a lot of X642s and the M445 (all metal have been balanced and sharpened and a few polished) and a lot of warm up graupner props
--2 x 2S Turnigy 5000mah 30C lipos
Selling my baby...highly modified brushless conversion of the Aquacraft Miss Vegas RC boat. This was built and modeled after ProperChopper's on OSE and was GPS'd at 61.7MPH with my cell phone in a Ziploc bag...don't laugh!!
$350 + shipping NO TX / RX
It has never been crashed and has been a shelf queen for the past 2 years. And includes the following specs...
--NEU 1515y 2200kv brushless motor with watercooling jacket ($230+) less than 15 min run time
--Modified watercooled 200A ESC with upgraded 5.5 bullet connectors setup for 4S lipo configuration
--high torque servo
--hull has been water sealed and fibreglass layed for rigidity
--rear wing with all hardware is included but I found it harder to tape up with the rear wing
--extra BRAND NEW 200A ESC!!
--extra BRAND NEW 1800KV Brushless Outrunner motor...will get you to just shy of 50 mph...good for practice runs
--octura x642 prop polished, sharpened and balanced which will get you into the 50s...if you want me to swap in the M445 prop for over 60+mph just say so.
Also have a Brushless Deep Vee w/ hardware 2200KV 180amp ESC...and yes those are REAL 25 aught 6 Remington cartridges (one was drilled out for the purpose of the exit point for the water cooling) on the rear of the hull which have been fashioned to look like exhaust pipes!!
$250 + shipping NO TX / RX
Its got a few spider cracks on the top of the hull but its never been crashed and I've repaired them so the hull is very sound. Its sat on my shelf for the past 2 years and has the following specs:
--2 x RARE Turnigy H3126 2200KV 1500 watts outrunner watercooling (1 installed w/ 20min run time, 1 brand new)
--180amp Turnigy Pro Brushless ESC with upgraded 5.5 bullet connectors setup for 4S lipo configuration
--extra brand new 60amp Turnigy Pro Brushless ESC
--high torque Traxxas waterproof servo
--hull has been water sealed and fibreglass layed for rigidity
--octura x642 polished, sharpened and balanced which will get you into the low 50s.
I can sell everything for $550+ shipping with the following...
--Both brushless boat rigs with brushless motors, ESCs installed, waterproof RX so both Ready-to-Run
--Boat stands for transportation
--2.4 Traxxas TX / Waterproofed RX
--4 rolls of clear hockey tape to secure the boat hatches
--Rear spoiler wing for Hydroplane with hardware for you to install if you'd like...I didn't like it installed because it always got in the way of taping down the hatch
--Grim Racer grease for main drive shafts
--A tonne of bullet connectors for your lipos to hook up the ESCs
--Brand new Turnigy 130A power analyzer
--Extra brand new water cooling motor mount for the Deep Vee Mono
--Extra silicone tubing for watercooling purposes
--Extra brand new Turnigy 3126 brushless outrunner 2200KV 1500 WATTS!! (the other is installed in the Deep Vee Mono) This motor is super RARE and the guys on OSE have already been messaging me to part it out!
--Extra brand new Turnigy 1800KV brushless outrunner
--Extra brand new watercooled 200A ESC
--Extra brand new watercooled 60A ESC
--All of my props....a lot of X642s and the M445 (all metal have been balanced and sharpened and a few polished) and a lot of warm up graupner props
--2 x 2S Turnigy 5000mah 30C lipos