Search results

JAE 91/101 built from a Zipkitts kit. Sponsons and skis are coated with graphite epoxy. The ski isn't glued down so you can attach with doublestick tape or glue it in place. Engine bay, bait box and sponson sides have carbon tissue glassed in place. Strut, rudder and turnfin holes have...

Hitec Lynx 4s with Proton telemetry receiver. I've had the radio out of the box, bound the rx and tested a couple of servos but have never used the radio. $200 plus shipping

X450, (X457 sold), (1655 sold), 1462. All 3/16” bore, sharpened and balanced. $30 each plus shipping. Sent from my iPhone using Tapatalk

.250” bore props both sharpened, balanced and never run. $35 each plus shipping. PayPal and I’ll happily shop anywhere in the world. Sent from my iPhone using Tapatalk

Sold Sent from my iPhone using Tapatalk

Irwin 45 pipe pressure tap added and wrapped in heat tape but never used or cut $60 Nova 45 and Mac 21 pipes sold Sent from my iPhone using Tapatalk

Sold Sent from my iPhone using Tapatalk

Older Roadrunner 45 with OS 46 VRM, complete hardware and Futaba servos OS 46 with new piston/sleeve and bearings Tuned pipe Stainless fuel tank New front spare sponsons 2024 tubing for spare boom tubes Prop $450 plus shipping and paypal fees

Too many irons in the fire for me to be boating at this time so sadly clearing out the fleet JAE 21 as shown complete with hardware, cmb vac 21, Futaba digital steering servo, 800mA Life pack and hitec digital throttle and needle valve. New Walt Barney tank Spare sponson set Mac 21...

After graduating college in '92 but before starting work I had the unique opportunity to help design and build a somewhat unique streamliner that could take a generic V8 small block of various displacements, fuels, naturally aspirated or blown, modern of flathead, etc. with the goal if getting...

I've heard that a few folks have fit the Mac drum rotor to the VAC 21. What is required for this modification?

So what are the pros and cons of mounting the rudder in front of vs. behind the prop? On my JAE 91 their hardware has the rudder in front of the prop. Due to the narrow tub I'm considering mounting the rudder to the side of the tub vs. the transom as the transom mounted rudder has the bolts...

I'm stoked to soon start building the first rc boat I've built in... many years. There's something about the smell of the parts of a model kit that brings you right back you when you started building models.

Picco P-90. Engine has good compression and comes with 1/4" sq drive collet, pinkert fuel injector, 5" rigid mount. I installed a new RPM rod when I got the engine but have not run it. $200 plus shipping.

Sold

Macs 15cc quiet pipe, has been cut 2" $50 CMB 15cc hydro header $20 Gas carbs and spacer $20 Octura strudder for 1/4" shafts $20 K&B 11cc mono header with 0.002" and 0.005" head shims $10 5" Muck solid mount for Picco 90 $10 Octura engine mount insert $5 OPS 21 cooling head $5 Mystery...

Getting back into modeling has got me in a nostalgic bent. If I recall correctly there was an article and plans for a 40 size SAW outrigger in MAN in the early/mid 80's. It was an unusual design in that the engine was laid on it's side so that it and the pipe were fully enclosed in the tub...

I've read through old posts and it seems that several folks were having problems with the VAC 21 when it came out. Seems the factory carb was causing grief. Also sounded like the engine preferred smaller props spun fast. I haven't measured the stock ports but my plan is to set them 130 for...

As shown CMB VAC 21 with unknown pipe. I purchased the engine used and have not run it. I did do an inspection, the cylinder has been ported, bearings appear to be in good condition and has good pinch when turning it over. The o-ring in the rotor housing was split so will need to be replaced...

Two NIB Picco p-zero .06 engines, strut, rudder, two Wohlt's 1/16" wire drive lines, two props. $275 shipped in the US.