Search results

Thought with the vastness of the web someone would have posted some tech info and pictures of 1/2 wave pipes .... no such luck finding anything yet :( If you have been around long enough you likely have seen / used those big straight wall cigar looking pipes of years past like we once used in...

Question for the brain pool among you R&D guys, Try stuff modelers Know and used Lead/Teflons, Brass sleeve in stuffing tube & Oillite bronze for strut/shaft bearings . IMO all work well pending application and prop size in use. Have ANY of you fooled around with synthetic materials such as...

Hull came in at 23# RTR with half full fuel bags. 52" hull ... 56 1/2" OAL at 30" wide. * One Big Azz Rigger !! Now a decent weather day on the BIG lake needed.

Need some help from you guys with BIG or TWIN rigger experience. Just finishing up my big gas inline twin and need to set up sponson spacing to establish the best footprint for size of this boat ... Input please. * Tub is 48" long at 5 3/4" wide, set up as a 3 point. OAL is 52", RTR weight...

* HendricX (61) * Scott Schneider (52) * Chris Wittrig (44) * Watercadet (29) * Will Nanney (21) * RickGlover (54) * Harald1966 (45) Bunch of us .... I off into the mountains for some snow shoeing monday :D

Taken from a link posted on JRCBD ... killer footage and editing !!

Was reading a post on another site My link about a big twin gas cat with outdrives that had riser tubes threw the cavitation plates so air was draw in ahead of prop, another poster had small tygon tubes under drives to draw in air ahead of props. Both these posters got my attention to a concept...

Those of you who have made the switch to 2.4 gig Am looking for some OEM futaba FM Ch78 RX crystals or Ch90 to work in the 113ip pcm receivers. They will have an I.D. type number of 72-12 on them along with actual frequency Want 2-5 of them .... what ya got ?

Just sharing my winter project for 2010 ... a FF rigger with shingled and tunnel ride surfaces. Powered by one of the new Korean RCMK rear x RZ-254 gassers, build was purpose built for it and to explore the pro's / con's of the ride surface mods that were the buzz a few years ago ... test test...

Took one of Toms FF gas kits purchased as Precut parts and worked it into a gasser of a different breed .... Should prove interesting :blink: http://www.jrcbd.com/showthread.php?t=34248

Guys am about to start building some Gas rigger sponsons and need some really good foam ... recommendations ? If you have some ( Mis-spelled ) Kledgisel or Spyder foam ... or ? your willing to sell me, let me know please. Need a chunk big enough to do 2 @ 16" fronts and a pair of rears. (...

Ok, know there is some of you guys who purchased Nova rossi's for boats and did not use the heat sink heads. I have a purple head Nova Rossi LS I don't use and want it for a 1/8 scale buggy project, need a head heat sink. Is the typical 4 bolt Layout, so a short or long stroke version likely...

Guys, Know this idea has been around with those in the know for years, but then again many have never seen such a simple tool. Here is a link for an article over at MGB dealing with gas engines. The basic idea can be sized for Nitro engines too. Thought it was worthy of a post here at IW...

For those who run gas .... Review of the New RCMK "EVO" now up at MGB .... http://www.modelgasboats.com/Magazine_Content/Engines_and_Accessories/RCMK_S-254_EVO/

Guys, I have a pair of ABC 2916/3 props prepared by Chris Hoffman ... AKA Dasboata Sharpened/balanced being quite thin and sharp. Props have been heat treated after the fact so no longer shiny. Never been mounted or run, they are NEW ! 1) RH rotation 1) LH rotation 1/4" shaft application...

For you guys whom have run, Do run or know a thing about twins ? I am doing my final assembly of a GAS twin and feel as designed / manufactured is not optimum as it came to me. This hull was never finished and never been wet, so changes are getting done now rather than later on. Questions...

Anyone have a stash, a source that makes them still ? ........ Help !! PS. Don't want the 707's version. Contact me at: [email protected] Thank You !

This is an older ABC offering, but a nice little fairly radical prop. Thinkin it could be a good gasser prop ? Who's used or tried one before (Nitro or Gas) ..... What are it's attributes :blink:

This is downright SCARY stuff, if it is true then our way of life is about to get a whole lot worse. Check this out, if you feel it has merit and worth sharing with others you know ? Please copy & share the URL with them Link: </a>

ABC - 62 X 100 SB polished & Thinned $15 62 X 85 SB polished & thinned $15 PRATHER - 250S SB Tip rolled $15 245S SB $15 OCTURA - X452 raw $12 X455 raw $12 2) 1662 raw NIP $ 25 pair X445 SB $12 X445 SB rolled $12 Payment by USPS money order or Cashiers check ONLY .... NO Pay-Pal...