- Joined
- Apr 14, 2008
- Messages
- 2,013
SOLD OUT
Ready to go including the 65C heavy duty battery and charge cable for the battery. These are seriously nice hand made custom starters and the ONLY starter on the market with full ball bearing supported shaft.
.
These are built using ATV starter that has been modded in about 10 different ways to make it better than it was. It has been modded for high quality ball bearings.
The shaft is now supported by all high quality ball bearings to make it considerably smoother more powerful and efficient at the same time.
Snout of starter was machined away and then front of motor can was bored to accept a high quality sealed ball bearing. The tail housing has had the bronze bushing removed and replaced with a stainless steel ball bearing. The thrust washers are removed that used to thrust against the inside of can ends and I made spacers that now allow it to thrust on the ball bearing themselves for a major decrease in friction within the motor. The armatures have been balanced.
The center can was also reduced in length as well as the shaft so the overall starter is over a inch shorter than it was with the same power actually more with the entire motor spinning and end play thrusting on ball bearings now.
The solenoids are Yamaha marine type.
All wire used is high quality silicone fine strand with nickel plated steel high temp terminals that are crimped, soldered and heat shrinked.
These new ones are similar to the ones in the video that I made last time with just a few changes. These are very nice and are modded ATV starters. High quality ball bearings have been installed at both ends of the armature and all the end play is taken out. The motor cans have been shortened as well as the snout removed and about a inch of shaft cut back and turned down to accept the dual groove pulley.
Smooth and powerful all ball bearing custom super high torque motors.
Wiring is all fine stranded silicone insulated with heavy duty terminals crimped, soldered and heat shrunk.
Ready to go including the 65C heavy duty battery and charge cable for the battery. These are seriously nice hand made custom starters and the ONLY starter on the market with full ball bearing supported shaft.
.
These are built using ATV starter that has been modded in about 10 different ways to make it better than it was. It has been modded for high quality ball bearings.
The shaft is now supported by all high quality ball bearings to make it considerably smoother more powerful and efficient at the same time.
Snout of starter was machined away and then front of motor can was bored to accept a high quality sealed ball bearing. The tail housing has had the bronze bushing removed and replaced with a stainless steel ball bearing. The thrust washers are removed that used to thrust against the inside of can ends and I made spacers that now allow it to thrust on the ball bearing themselves for a major decrease in friction within the motor. The armatures have been balanced.
The center can was also reduced in length as well as the shaft so the overall starter is over a inch shorter than it was with the same power actually more with the entire motor spinning and end play thrusting on ball bearings now.
The solenoids are Yamaha marine type.
All wire used is high quality silicone fine strand with nickel plated steel high temp terminals that are crimped, soldered and heat shrinked.
These new ones are similar to the ones in the video that I made last time with just a few changes. These are very nice and are modded ATV starters. High quality ball bearings have been installed at both ends of the armature and all the end play is taken out. The motor cans have been shortened as well as the snout removed and about a inch of shaft cut back and turned down to accept the dual groove pulley.
Smooth and powerful all ball bearing custom super high torque motors.
![fDu7fwD.jpg](https://proxy.imagearchive.com/7da/7da2fae26c4e841a90baec764c34bb34.jpg)
![aow67c.jpg](https://proxy.imagearchive.com/d1e/d1ed21490f4ff7c571542142b9d0d8e1.jpg)
![4UXNp35.jpg](https://proxy.imagearchive.com/274/2740e07ad10f0a8c9275afdd4d1ef0c9.jpg)
Wiring is all fine stranded silicone insulated with heavy duty terminals crimped, soldered and heat shrunk.
![eQIbPxb.jpg](https://proxy.imagearchive.com/428/42844e2b73f34adc244e8bb31e6b1ae5.jpg)
![LVQRaOy.jpg](https://proxy.imagearchive.com/ad8/ad806ce512894ce61e008e702345f5ae.jpg)
![gE9xIT4.jpg](https://proxy.imagearchive.com/125/1256cd62e1d59e6a4c2a68d77beca3aa.jpg)
Last edited by a moderator: