Gas Mono Props

Intlwaters

Help Support Intlwaters:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

Bob English

Well-Known Member
Vendor
Joined
May 11, 2010
Messages
159
These are all sharpened and balanced props. The first prop is a 3014/2 20* .50 prop. It is one of the newer props ABC has come out with. For a long time if you go back ten years the 3014/2 was always a good mono prop. But it needed to be modded to run good on a mono. Back then it was only made in the high lift 10 degree rake. To make a good runner you had to cut back the tongue a little and then do a back cut to get some of the lift out of the prop. This new one is now a 20 degree rake prop. And if you look at the two blade .50 bar props you will see as the rake goes up the tongue gets smaller. Now no need to mod them. The second prop is a 2814/3 choppper. It is also a 15* rake prop. It is the one prop in the ABC line designed for a mono hull boat. The third prop is a modded 2817/2 19* .50 prop. I have done a lot of these props for guys to run on the mono hull gas boats. It is a fast prop. You can see it in one photo next to a VooDoo Tater-XX prop. The Tater has always been a popular mono prop. It is a 7016/3 with barr cuts and round tips. If you look @ this mod 2817 it is like a big Tater-XX prop. But larger diameter and more pitch. The Tater was always good on a 260 but to small for a strong 29.5 modded engine. This mod 2817 is to much for a 260, but makes a great big block prop. Also the 3014 and 2814 chopper props are more for a good modded 260. The 3014 is a $50.00 prop and the chopper and 2817 are $70.00 each props. The USA shipping is $5.00.
 

Attachments

  • P1210549.JPG
    P1210549.JPG
    2.8 MB · Views: 78
  • P1210550.JPG
    P1210550.JPG
    2.7 MB · Views: 77
  • P1210551.JPG
    P1210551.JPG
    2.8 MB · Views: 71
  • P1210552.JPG
    P1210552.JPG
    2.8 MB · Views: 65
Shane since I only have one raw one left let me get it done before you send a payment. I just want to make sure it comes out perfect. I'll get it done either today or tomorrow.
 
Peter, if you were asking about the Tater-XX I show in the one pic, if you want it I'll sell it to you. I was a new prop I had and was using it as a example to show the size of the 2817 prop. But for many years I was a Voodoo dealer and sold a lot of the Voodoo props. But a couple years ago I just kind of backed off the line. There are still some new ones out on the peg board. The Tater is a 7016/3 prop that has the tips rounded and has barr cuts. This one is finished and ready to sell. But it is the last Tater I have left. I don't have a second one. This prop is made in 17-4 stainless steel. Very thin and very sharp! It is a prop I sell for $70.00 plus the USA shipping of $5.00. Let me know if you still want it.
 

Attachments

  • P1230553.JPG
    P1230553.JPG
    2.7 MB · Views: 33
  • P1230554.JPG
    P1230554.JPG
    2.7 MB · Views: 34
  • PC190533.JPG
    PC190533.JPG
    2.6 MB · Views: 38
  • PC190534.JPG
    PC190534.JPG
    2.5 MB · Views: 39
  • PC190535.JPG
    PC190535.JPG
    2.5 MB · Views: 35
Back
Top