Search results

The kind of companionship that you pay for...... The owners have gone to great lengths to improve the quality of the establishment and clientele in the past few years, but it would not surprise me to find that services are still available. The state of California has a policy which allows them...

Motel 6 is the lodge of choice for those who might seek post race companionship......

The old HD stuff had a lot of issues which have supposedly been addressed. All of it, old and new, uses moisture and temperature sensitive adhesive (85* F max) and needs to be installed with temperature expansion taken into consideration. Just had 2K sq. ft. installed in an Arizona mfg'ed...

Saw JW live on only one occasion... he did a few tunes with Edgar's band White Trash at the Hollywad Bowl in '71, opening for ELP and Humble Pie. Unfortunately, he wasn't allowed the freedom to play his better stuff. One of the very best of all time and certainly the whitest of the white blues...

Found this supplier a few weeks ago.... www.alexandriaprecision.com

IMHO Senna was incomparable.... then and now. Watched him race live for 3 years here in Phoenix and in many televised races and qualifying sessions. He was not always the most publicly presentable or F1 fashionable personality and was often controversial in his battles with rivals. In his...

Getting a similar message on www.rumrunnerracing.com ..... interesting that two boat sites should misbehave at the same time.

Some have tried the Mamba Monster 2 "waterproof" esc's in boats with the factory cooling fan, though I'm not aware of anyone adding water cooling plates. With the fan, CC rates them to 120 amps continuous..... more than enough for spec racing.

The quoted 20:1 failure rate has been due in a large part, to lack of knowledge and abuse on the part of the users.... granted there have been lack of foresight errors on the part of the CC design team, but then they used that as a learning curve. Was once told by a CC tech that they used the...

Been using Castle Ice, Edge and Talon ESC's with water cooling plates for almost a year. No problems yet.....

A short note published in the Az Republic today said that the reason stated by the judge for gutting the FCC rules was that they did not go far enough to adequately regulate the industry..... told the FCC that they needed to rewrite the regulations with some enforceable power behind them. But...

Unless AMA has changed their coverage in the last couple of years, I think you'll find that theirs is a secondary policy. AMA will only cover what your homeowners insurance doesn't. Both IMPBA and NAMBA have primary policies, meaning that their insurance covers you prior to your homeowners...

Darin- I've used carbide burs similar to the McMaster #4284A24 to start the hole. Dimple each side until it breaks through using low speed and side pressure (not straight in), then open up with the proper sized drill bit using the correct speeds and feeds. It works on both high carbon and...

My Lynx setup instructions say 7 1/4" to 7 1/2" initial CG without fuel, but does not specify if it is measured from the transom or aft edge of the sponson.

As the sign-up and scoring dude at the NAMBA 2012 FE Nat's, I can vouch that no, none, zip, zero nonmembers were charged more than $10 for the entire event. However, I did sort heats with each day considered an individual "event" (program nomenclature) to make it easier to manage the limitations...

Every race day is an "event", just as every heat race during that day is an "event"..... as is every pass, missed buoy, lane infraction, etc.. Not sure if any organization defines "event", but it's generally assumed to be a race meet for whatever the duration. Don't ask me to define "race...

The NAMBA single event fee of $10 is good for all three days at our Winter Warmup race. I'm assuming that is why NAMBA calls it a single event fee and not a single race day fee.

The topic has been discussed..... IMO, the use of electronic limiters would only result in the need for motors whose power parameters are specifically designed to be used with limiters. So much for cost reduction..... :rolleyes:

The wife hasn't watched the Food Channel since they axed Paula Deen, but that engine cowl on a PX335 reminds me an awful lot of Giada De Laurentis.... the head is way too big for the body! :P Other than that it looks great!

Got to tell these a-***** that I switched jobs from KFC to the car wash nextdoor because it was a ten cent raise... $1.35 an hour from the then minimum wage of $1.25. Oh, but of course everything was cheaper then...LOL. And 95% of the population were too proud to accept food stamps or welfare...