Search results

I have a K&B 3.5 inboard engine for sale. Never run. $110 US, shipped in the lower 48 states. Can ship it next Wednesday (up North fishing till then) PayPal only at: [email protected]

Thanks Tyler and Mic, I'm guessing I should put foam in it everyplace I can. That actually reduces buoyancy, but may save the boat if it ever had a hole punched in it. Do you guys do that with foam?

This is my first FE boat, so please forgive my ignorance. I have a question about weight. I am building a Zipp 33FE as either a P or Q. As a Q, I am using a 2S and 3S 5,000, 70C in series and it is really heavy. I made the front sponsons wider (width of a 45 boat) anticipating some extra...

Here is a little story about Rod: In 2020 we staged a little club race in Eau Claire, Wi for the purpose of getting Rod out to see some boats. I was very surprised when he told me that he had never actually driven a JAE hydro, hence an important purpose if the "race". So we put him in a lawn...

Gentlemen, I spoke with Rod a few weeks ago and we talked about his time in Nam, and he told me he knew God was real when he was spared while the guys next to him were taken over there. I am very sad he has left us, BUT I shared the gospel with him then by reading Romans 10:9-10 to him. It...

This worked out good then. Mine will go to Chris Capaldi, who just PM'd me that he is also looking for one.

I have one also if that doesn't work out. Mine has a step cut in the bottom, which we used to do early on to make the strut bottom flat with the ski.

JAE 45 with CMB 45 at 6.1 lbs. JAE 21 GT with CMB 45 at 5.1 lbs. This boat is fast and quite stable.

Nub Kopisca has a park in Ocala that the park people approved for running boats. It's called Tuscawilla Park. I ran there all the time when I was in Florida living in The Villages few winters ago. I will send you a pm with Nub's phone number.

That makes perfect sense Jim. Thank you!

Jim, When you press the larger bearing onto the crank up to and against the counter weight, how to you get it off when you change bearings? I'm imagining chucking the bearing in a lathe and pushing the crank out from inside the spindle. Is there an easier/better way? Why do you want C-4 vs...

I made a request to the company Terry mentioned. The response I got is below. Just FYI. (I asked for front and rear bearings for CMB 21 and 45 engines. They only carry the larger rear bearing). Bob

Good video Terry! Never thought of putting the green sealer on the crank like that to stop slipping on the crank. I tried some ceramic SiN, C3 fit bearings from Boca in my CMB 21 recently. They claim they are rated for higher RPM and need very little oil. The second time I ran the boat one...

I am using one on a 21 Evo in both an outrigger and in my 21 mono. I like that they are 360 degree carbs without a hard stop. Before you get one, make sure you have room for it because it is quite a bit longer than the stock carb. It certainly performs as well as the stock carb and maybe...

Have you ever wondered exactly how much of an effect changes in air density and humidity have on engine power? Here is a link to a calculator that you might find interesting. It assumes you have 100% power at a reference condition of: 77 degrees F, 29.235" Hg barometric pressure, 0 feet...

Ours work fine even with no window and through carbon fiber lids on 10 different boats. Every now and then (like 1 in a 100 times) it will glitch and say we were going 350 mph. We just turn it off and start over and it works fine. I know its not supposed to work through the carbon fiber, but...

Calling John now. Sold pending payment.

Mike, What tool do you use to engrave the number on the hub?

This is a new carbon fiber cowl manufactured by Brad Nichols. We ordered it for a JAE 21 GT but never used it. We paid $60. For sale for $50 shipped in the lower 48 of the US. PayPal only for payment. Note that there is a manufacturing defect at the aft end of the cowl. This is the...

Tom, tracking number is in a PM to you.