Search results

Intlwaters

Help Support Intlwaters:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. XtremeRcBoats

    DIY twin motor mono build 'G-Force'

    Dirk-jan, too better protect the electronics you can also spray/soak them with CorrosionX. That is what I normally use.
  2. XtremeRcBoats

    Boats Wanted Looking for SGX 90-101 or similar

    Check out this twin not sure if if is still available https://www.intlwaters.com/threads/cmd-eagle-sgx-twin-80-cmb-80-race-ready-for-sale.81433/page-2
  3. XtremeRcBoats

    .21 Outrigger recomendations

    Or check with Derek Owen, he is also from the UK.
  4. XtremeRcBoats

    .21 Outrigger recomendations

    Ricky, there is a guy that built riggers (Jae and possibly others). You can buy them pre assembled from him. His name is Mike walker, he is also on this forum. Not sure if he still builds them. I would suggest to check with him.
  5. XtremeRcBoats

    DIY twin motor mono build 'G-Force'

    Looks great again. What I've seen with long rudder brackets is to add a horizontal brace for stiffening instead of vertical. Do you feel it was going up and down?
  6. XtremeRcBoats

    LiveTime/MyLaps– Lap Counting System

    Alex, they are used for both, also for fsr-o, the offshore class
  7. XtremeRcBoats

    Cmb 21 vac

    Drew, for your information. CMB came out with an updated carb as more people had the same issue. See picture below of old (left) and new carb (right).
  8. XtremeRcBoats

    twin mac 84 problems

    Interested to see the pics. Still have some mac84's also in a twin (Probably the old ones).
  9. XtremeRcBoats

    Boris Mosier 2 pump flow meter

    I've also upgraded mine to lipo and got a ubec voltage regulator for free back then from Boris, what a great service that was. I run mine on 5v, thar is what Boris recommended.
  10. XtremeRcBoats

    DIY twin motor mono build 'G-Force'

    Nice project again dirk Jan. You are a fast builder. Did you cut the frames out by hand?
  11. XtremeRcBoats

    32" Wild Thing build thread

    Ouch that hurst, but looks like new again. How did you end up in the shore?
  12. XtremeRcBoats

    Glow igniter!

    Show us the result. Good luck!
  13. XtremeRcBoats

    Weekend project

    Bruce, have you already tested your starter? I finally received the relay. Also compared the dynatron with the starter. I think indeed a speedmaster handle will not work. Question on the relay, I presume the wire is the + for switching the relay and the housing is the -? Mike, Bruce few...
  14. XtremeRcBoats

    Glow igniter!

    forgot to add, I'll be using a 3s Lipo. Testing sofar was done with a 13,8V power supply
  15. XtremeRcBoats

    Glow igniter!

    The one i have only has 1 potmeter, this is to set the output voltage. With the version with 2 potmeters (i think) you can limit the output current.
  16. XtremeRcBoats

    Glow igniter!

    Hi Bruce, yes it will read out the amps, see below screen shots, the left is a O'Donnel Blue and right is a K&B 1L. these are very cheap components, so maybe not 100% acurate but gives a good indication. This is what I've used for it: PCB...
  17. XtremeRcBoats

    Glow igniter!

    That is why I have added the amp meter, if it stays 0 when I connect the plug, it means that it is broken.
  18. XtremeRcBoats

    Glow igniter!

    It was a bit tight but got it in. Next time will use a bigger box and add a small lipo in there as well.
  19. XtremeRcBoats

    Glow igniter!

    Looks great. I'm also building a glow igniter based on a xl4015 pcb and have added a amp meter on to it. I'm now putting it in a small box. Will power it from my starter box.
  20. XtremeRcBoats

    32" Wild Thing build thread

    Looks great, you're very skilled. Normally you make mostly right hand turns, so the left turn fin can be smaller then the right side turn fin.
Back
Top