After much debate i've decided it's time to start finding homes for some of my extra stuff. First to go is a pair of 3PJ radio sets. One TX is 3PJ Super. Both radios are 75 mhz with synthesized RF modules. Each comes with a LiPo battery pack and r113i receiver. $85 ea shipped in USA. Buy both...
I have become aware of the possibility of some 6002 and 6002A bearings that I have sold might not be genuine WIB. The suspect bearings were labelled as Swiss Manufacture, but did not have WIB engraving applied. When I received these bearings from my distributor, I immediately called them to...
I just tried to log into the IMPBA website and was advised that my membership had expired. I'm a Paid Life member, hence my membership does not expire until I do.
edit: contacts were correct, I was mistaken.
Like the title says, NIB MAC21 OB powerhead. Prepped by Rod Geraghty. Never seen fuel. Includes both water and air cooled head caps. Selling to fund another project. $350 shipped in US48. Will include a complete Irwin Lower with an Oval Express propshaft assembly for $425 total shipped. SPP OB...
I received several NiMh 6V RX batteries with a radio purchase. I run LiFe, so I don't need these. They appear to be fresh. I will test them with a charge/discharge cycle to confirm capacity. Looking for $5/pack with $6 shippiing for 1 or all. I can't remember if there were 4 or 5 packs, and I'm...
I have a couple Black head OPS90 motors and many parts. 1 motor is just barely broken in, the other has a new P/L and cylinder/cap assy with new HS WIB bearings installed. Both motors come with 1/4" Seromarine collets. For parts I have rod clips, exhaust header gaskets, rod needle bearings...
Does anyone know if there is a crapshooter style cowl that fits a MAC84 carb setup? Sent a PM to Stu, and am waiting for a reply. but am looking for options.
I have many R113iP PCM receivers on 75mHz for sale. $30ea. $5 shipping for as many as I can out in the box. I also have several 75mHx modules and xtals. $20ea.
Clearing out unused items. I have a NIB Ace R/c Digipulse multicharger (SOLD). Ace Digipace II cycler. Also as new condition. Will cycle both TX and RX at the same time. $75 shipped. I'll throw in all the NiCd and NiMh battery packs I have. I'll also throw in a 10 cell A/C NiMh charger and appx...
Time to thin down some of this stuff.
OPS90 with 1/4" Aeromarine collet., OEM header, and spare header gasket. compression is as new (super bump at TDC) - $300
OPS90 rod circlip NIP - $4
OPS90 rod needles NIP - $12
OPS90 front housing, excellent seal bore, will install new WIB bearings for...
I no longer have a need for this charger since changing to LiPo and LiFe batteries. The charger has hardly been used since I went idle shortly after purchasing it. Will charge up to 6 packs at 1 time 10mA - 150 mA rate on each circuit. $85 shipped to you. I also have an Ace cycler that I will...
Swiss and German bearings with polyamide retainers. Popular sizes usually in stock. Next day shipping. On IW as thrcboatracer and email [email protected]. I hope to have a web site soon.
In following the thread about head buttons and the brass material, I had a brain cramp. I used to work in the injection mold sector, and we used heat sinks from a berillium alloy for the strength and thermal conductivity. Any thoughts on using this type of material for head buttons? I'll get the...
I have a few motors and parts to move.
1ea OPS90, barely broken in. Very tight fit. $300 + USPS shipping (~$10 priority mail)
2ea NIB OPS 67 (converted DF motors) $225 ea + USOS shipping (~$10 priority mail)
2ea used OPS 67 race motors, EC 1 drum w/billet front hsg, 1 OEM disc. Drum=$175...
I have several R113iP receivers for sale. All are 75mhz. $35 ea + $5 shipping. $5 shipping covers up to 4 receivers. SOme are original antennas, some have deans base loaded anttennas (included) Let me know what you want. I also have a Futaba 133RF(?) micro receiver on 75mhz. ANd mayeb a cople...
I need to find some nuts for some BVM needles I have. I thought that they were 1/4-28, but that doesn't seem to be right. Maybe it is 6mm fine thread. Anyone know the thread size of the outside of the body, or have a couple of spare jam nuts to mount the needles?
Seeing the thread about power pancels got me thinking. I use a dedicated battery box for my started so I don't want the fuel pump and starter plugs; but I do want a plug driver and display. Does anyone know of a good plug driver panel with digital display? I have considered buying a full unit...
Not quite broken in yet. Engine has less than 2 qts through it. I've decided to stay with my MAC67's now that it appears that parts will be available again. Includes collet and header. $250 shipped in the USA.