Search results

Here's my scenario. My throttle and mixture servos are rated at 4.8v to 6v. I want to use a steering servo with a range of 6v and up. I'd like to switch over to a LiFe battery which is 6.6v. Will that voltage damage my throttle and mixture servos?

What is being used in gas outboards for steering? Servos? Voltage? Steering rods?

I'm sure there's a thread on this in here somewhere but I'm unable to locate it. With the larger steering servos requiring 6 to 8.4 + volts how do you wire to the receiver on gas or nitro boats where there is no speed control involved? I’m using the Spectrum DX4C and my servos are a mixture of...

I'm sure there's a thread on this in here somewhere but I'm unable to locate it. With the larger steering servos requiring 6 to 8.4 + volts how are they wiring that with the transmitter on gas or nitro boats where there is no speed control involved? Is the battery pack plugged into a BEC device...

Been out of the sport for awhile and my 12v gel sealed batteries finally died. What is everyone using for their electric starters now?

I have available the Miller American U 00 built from Roger Newton Plans #146. This hull originally ran with an open driver area pre 1987 and in 1987 was revised to an enclosed canopy. That hull was known as the Star Wars Miller. I saw this hull in person in 1987 at my first Unlimited race in...

I have a Rossi 61 for sale. Bearings feel smooth. Has the carb, exhaust throttle. Looking for $125 plus shipping costs.

I have a Picco 90 for sale with carb and exhaust header. Bearings feel smooth. Looking for $200 plus shipping.

Looking for an aluminum header for the K&B 7.5 OB to mount an Irwin pipe.

I've relocated to Lebanon, TN and am looking to see if there's any nitro R/C going on anywhere near me.

I have a Rossi .61 marine to sell. Don't know it's value so feel free to make an offer. I'll accept PayPal in the offer but shipping will be in addition and at cost.

Picked up an Irwin Pipe for 7.5 OB. Looking for the recommended mod's to this pipe for 7.5 OB, stinger ID and length. Will be using it on a K& B and a Nova Rossi. Can anyone share please?

Almost done with this years race tunnel. Radio is on order and will order the O/B next weekend. Then I'll switch to a new development hull I'm putting together. Looking to enjoy this year with the Badgers in WI.

Not sure where to post this but I'm looking to see if anyone has access to a vacuum former that could make a couple of cowls for me at a reasonable price. Cowl would be about 28"L x 7"W x 5"Tall. I'll provide the plug.

K&B .67 OB motor serial number G95067. Was rebuilt by Rod has been stored since. Looking for $250 obo plus any additional costs for shipping or Paypal. I travel a lot so be patient with the timing of responses.

I'm planning to finish my 1/8 scale Miller American U00. The 1987 APBA Gold Cup boat that was nick named Star Wars because of the canopy. The hull was constructed using Roger Newton Plans. Can anyone provide me with the color number of the red used on this hull? It's a single shade of red not...

Rossi 61 $150 plus shipping and any Paypal fees K&B 67 O/B $200 plus shipping and any Paypal fees Picco 90 $250 plus shipping and any Paypal fees

I have three OB motors that I'd like to know what a decent price would be for each one. Not lookin' to break the bank and not lookin' to give them away. Just looking for a fair price. First 7.5 OB Rossi probably around 4 years old but a little more than a gallon of fuel run through. Ran the...

Want to put a GPS in the boat to give top speed. Can someone provide me a source? I understand there's one out there that weighs 2 oz.

Looking for input from those that run 7.5 tunnel. I have two motors that I run a Rossi and a K&B. I design, build and race my own design and have not ever really worked with props all that much. Currently I run X447 sharpened and thinned. I'd like to experiment with some props and am looking for...