Hey guys,
As the topic says I am looking for a replacement Rudder Blade for a 45 Eagle SG. Any suggestions as to a good replacement will be appreciated. I have talked with Andy Brown but he doesn't have any available.
Thanks,
David
I have an 45 Eagle SGX hull that replaced an Eagle 45 SG hull that broke in half in a crash several years ago. I am running the SG sponsons with the SGX hull. Even though the boat runs really well, it wants to walk the sponsons very very bad halfway down the straights, which can carry into the...
Ok, can you use any type of fuel filter for nitro fuel? if not, what is the best type of filter for nitro. This filter will be used to filter from the container to the tank in the boat.
Thanks in advance,
David
Ok, guys, Now I am looking for a replacement cowl for an Eagle SG 20 hydro rear exhaust (flywheel side). Yes, I know some people call that the front! LOL! My current cowl is beat up and getting brittle.
Thanks,
David
Price dropped: MAC 45 Complete Engine parts - $ 150.00 shipped USPS lower 48
Engine needs some TLC, Case\rotor housing O-ring, threaded end of crankshaft has a chipped end but did not effect the collet attaching. Ran it that way with no problems. I don't run Nitro anymore so I am selling it...
Lawless 3.5 lower unit for sale - As pictured. No Steering arm or hinge pin.
Lowered Price to $100.00 (shipped lower 48 states).
Paypal only : [email protected]
https://www.intlwaters.com/uploads/1202227861/gallery_285_201_1250363.jpg...
Anybody ever own one of these? Back in the mid nineties when I was also into Tunnel boats, I was real close to buying one. Didn't really care if it ran well or not, just thought it looked cool!
Back Ground: The last time I ran the boat I lost the cowl, so I got a new one cut a few holes in it and threw it on the shelf in the garage where it has sat since.
A weekend ago, I threw my 40 rigger that I hadn't run in 2 or 3 years in the water to get it ready for a race this weekend. What I...
I am looking for a 3rd fuel mixture control for a .45 rigger of mine. Who sells these things today? I am in need of one ASAP for a race coming up next weekend. The one that I have is an O.S. In-Flight Needle Valve, The O-rings have gone bad and I don't have any spares.
I know that this probably has been asked before, but who carries good bearings that will fit the MAC 21 and 45 engines. I might possibly be looking to replace the piston and liners in the near future, also. Any help would be appreciated.
Thanks,
David
Just like the topic says. Has anybody returned to running nitro boats after running gas boats? I have just about given up on gas boats, they just don't do anything for me. Still have my nitro boats. I don't care about the cost of fuel or glow plugs.
David
Sale Canceled
I have two MAC .45 engines for sale. I really hate to part with these, but nitro is dead in my area. It's all GAS now. The engines are used, but ran well the last time I raced with them, which was over a year and half ago.
When I ran these engines I replaced the bearings every...
This is the surface drive hull. I think my hull has too much hook. How much hook should be on both sides of the bottom of the hull? How far should the hook be from the transom? If you look down the bottom of the hull the hook is very visible. Even on rough water it wants to plow through the...
I am getting rid of all my Outboard stuff. I have one 3.5 O/B pipe, two 7.5 O/B pipes (one muffled-Irwin) and one header. The header fits a CMB 45. I used to run these pipes on my .21 and .45 tunnels a few years ago. They ran quite well.
I also have a 40/60 tunnel, and a Lawless 7.5 lower unit...
I have the following Octura and Prather props for sale. Some are raw, some are sharpened, none are totally balanced, as noted.
These are props that I don't have a need for anymore and would not hesitate to finish them up and run them.
All are $15.00 each shipped USPS.
I accept Money Orders...