Search results

I gave Kevin the JVS hull. He will collect shipping from you for that and the engines.

Reply to tag lilne...... Pitman tries to tell driver to use left thumb but driver does listen......

JVS hull. Never drilled. Kevin and I live in the same city if you want his NR 46 motors. I can throw in the boat......

The only props I have had trouble with is an H-29. Probably from the Tidewater days, not the current ones. Tore a blade off of 2 of them. I liked them on my X Hydro. Smaller diameter but pitched up so the engine would rev. Just couldn't handle the load.

Jim Wilson used a AA Nicd battery i an A Mono. He used to run so much fuel through his motor, the plug needed help staying lit. I tried it on an A Mono and it made a difference, bringing up the revs, at idle when it was connected. Can't prove that it helped me much in a heat. The main...

So, does a flat piece of aluminum placed 6 inches to 1 foot behind the boat constitute a "shrouded" propeller? This seems to be the standard from the NAMBA Nats that I have attended. Would 2 inches be OK without protection from the sides and above? Just looking for what "shrouded" means...

I have 2 H-2 props and one that could be an H-2. The latter has a smaller hub and I can't read it directly but the diameter and pitch are close to the 2 others.

At our races (D16), our hot pits and working pits are one and the same. We all have prop guards of some sort. Some more elaborate and some so so. I've seen "cake pans" and other barriers at the NAMBA Nats and they are a joke. Some people put their boat facing away from the "prop guard" and...

Re; Using in a Catamaran. I have two electrics with .078 wire drive I built myself. P hydro and P mono. I'd say that a wire drive in a big cat would not work well as the ones I've seen have very tight radius for the stuffing tube. The whole trick to a wire drive is keeping the bend as...

In the mid 90's I tried to run 75mhz on a couple of boats. I went to a Nats where there were a lot of 75 mhz and had no end of problems with interference. My boat ran fine until certain people fired up their radio and the boat went nuts. I took two radios with different channels into a...

I built a Q hydro out of an older model Eagle SG 40. With two 4000mah 6s, ESC and SSS motor, it comes in at 10 lb in running weight. Batteries are in the two front compartments and the motor is back where the radio box would normally be. CG is at the back edge of the turn fin. The Eagle...

Zipp Kits has carbon booms that should fit an Eagle 21 and 45.

Yes. But it's a fine balance. Too little gap and the tension can be too much. Just want it to lightly push on the strut. I can tell how much push I get by how the delrin washer wears. No wear, and I'm pushing all the time on the motor, a little bit of an indent from the strut and that's...

I am running brazed cables I build myself. For a .21 hydro, I leave about 1/16 gap and on larger boats, about 3/32. Never had a problem with the cable pulling apart. The cable goes into a bit of tension but not much. The rubber mounted engine engine will move a bit if it gets into too...

I run my flex so that it goes into a bit of tension when running. This keeps the cable from twisting up. The teflon liner definitely helps keep the friction down in this case. Jim Wilson convinced me on the merits of keeping the gap small between the strut and the drive dog thus allowing the...

Parts are all sold.....

Actually, a cheque works better for me. I don't do much paypal and I have not figured out how to get the money out of it yet. I will message my address.

$550 would be fine by me.

Via Canada Post/USPS Express post (one better than basic) estimates $100CDN and I will pick up the first 50.