Search results

Intlwaters

Help Support Intlwaters:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. Davidkrienke

    260pum starter pulley needed. Will this work?

    https://www.ebay.com/itm/144808174130?_trkparms=amclksrc%3DITM%26aid%3D1110013%26algo%3DHOMESPLICE.SIMRXI%26ao%3D1%26asc%3D246215%26meid%3Da44a31361cb14facb41c5cca40af7ec9%26pid%3D101196%26rk%3D5%26rkt%3D10%26sd%3D255147796732%26itm%3D144808174130%26pmt%3D1%26noa%3D0%26pg%3D2047675%26algv%3DPromo...
  2. Davidkrienke

    21 billet Carb Id needed 12-18 carb advice needed as well.

    I have this Carburetor for a 21 and I don't know if its worth trying over the os 20j carbs I normally use will it gain anything I wonder . anyone that has used one could you chime in please. Also what are these spray bar inserts for ? I don't have any carbs that fit them. Also I Need a carb...
  3. Davidkrienke

    oval race boat sinks in a few seconds

    Warning camera man cusses after wreck.... Just thought they were cool boats thought I would share. Mean sounding engines,
  4. Davidkrienke

    Toroid propeller Has anyone tried one of these propellers on there real boat?

    I have been aware for a year or so but my son said they have been 3d printing them I wonder how hard it would be to mold one in beryllium ?.They seem to take the tip drag way down.
  5. Davidkrienke

    Provee Prop and Pipe help needed.

    I have a provee I am working with that has a chinese 29.5cc and the zippkits drop down header with a ebay pipe. I am noticing that I am not seeing the rpm that I am compared to my 26cc engine. I have the pipe as short as i can maybe can go another 1/2 inch if I put the clamp in the mandrel bend...
  6. Davidkrienke

    3 more boats finished for spring.

    I was able to get the motor in, header welded tighter to not cut boat and stuffing tube installed and everything else on the 42 seaducer gas conversion. Then I received all the parts for my provee from zippkits and built this whole thing I had just the hull from my brother he bought off ebay. I...
  7. Davidkrienke

    Gas carburetor start needle setting suggestions needed.

    I have 3 engines I need to get running and am unsure where these needle start points would need to be unsure of the carburetor numbers atm. 1st is a old bob hansen quickdraw 26.5cc going in a arty wood boat off ebay he is going to run. 2nd is a china zenoah 26cc ebay motor I just put this one...
  8. Davidkrienke

    Dynamite .19 for small rtr and jae12 update.

    I finally was able to get around to degree wheeling this little engine. And with two 3 thou spacers made from coke can aluminum I was able to come up with these numbers. intake rotor open 212 intake rotor close 61 transfers 128 exhaust 184 blowdown 28 squish 7 thou I have ran 3 tanks on the...
  9. Davidkrienke

    Muffled tuned pipe. Heaviest thing on earth

    I bought a pipe off ebay because I wanted a muffled pipe it arrived today and the thing is a tank. weights 24.5 oz . what do most steel gas pipes weigh. If I go with the zippkits pipe does anyone have one they can weigh? I just cant think it would be good to have that thing hanging out the back...
  10. Davidkrienke

    Bushwhacker 20 hydro copies of instruction booklet needed,

    I have a bushwhacker 20 kit I would really like to finish. I need new instructions though as they had been stuck together and are just a mess. Would anyone have a copy? . also any finished pictures of one would be super helpful. I think its all there just not sure yet.
  11. Davidkrienke

    Could someone id this hydro?.

    I had picked up this with another kit and curious to what it is? It looks like a neat old boat but with the wide center section and the sponsons close to the body like that will it be a good running boat if I put all the work into finishing it? Any info I would appreciate on this one.
  12. Davidkrienke

    K&B 7.5 piston pin nylon retainer glide ? is missing.

    I picked up a engine that is missing the piston pin glide on the pin and has been started and put a couple scratches in the sleeve that are pretty deep. can it be saved and would anyone have a nylon glide that goes on the pin for me ?
  13. Davidkrienke

    Jae12 from yesterday first run

    I was able to get pauls boat running yesterday I bought from him. I tried a few props . This is with a back cut and detounged x438 prop. It was doing the hop hop I am unsure what to do to fix it? Was it just the rough water ? I tried a 1440 mark prepared and 30 percent fuel couldn't pull it ...
  14. Davidkrienke

    Tunnel Hulls Video pretty neat footage of them flying the boat .

    Check out these tunnels flying. Just amazing
  15. Davidkrienke

    Novarossi Auction out of business ?

    I heard on a video that novarossi has sold there equipment at auction and is no longer going to make motors ? It was a oct 21 video on glow plugs. . Can anyone confirm this ?
  16. Davidkrienke

    Northwind 40 drive strut is offset .Why ?

    I picked up a northwind 40 and the drive strut is not centered but pitched to the left. does anyone know why this was done this way ?
  17. Davidkrienke

    Wall mounted boat stand Idea we tried.

    Getting all the boats put somewhere is getting to be a challenge lately. My son and I came up with this idea. We used a drill guide to drill them at a slight upward angle. Still somehow one dowel got messed up even using that . but this seems to hold the most boats in the smallest amount of...
  18. Davidkrienke

    Parts Wanted Nova .21 head button needed for GO .21

    I have a new Go .21 that has way to much squish .017 and wanted to see if anyone had a nova head button that would fit and maybe get the squish closer to .008 . Or if someone reads this that knows where to get mine machined I would appreciate it.
  19. Davidkrienke

    Go .21 head button needing turned down to set squish

    Would anyone be able to help me with a go.21 7 port head button. Its squish is .0017 and I need to get it to .0006 to .0008
  20. Davidkrienke

    Parts Wanted Aquacraft Lucas Oil or Motley Crew Cowling needed

    My son had his Cowling blow off his lucas oil boat and it went to the bottom of the lake. if anyone has one let me know Thanks.
Back
Top