Search results

Intlwaters

Help Support Intlwaters:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. Davidkrienke

    Eagle Hydro stand

    That really came out nice. Good job.
  2. Davidkrienke

    Sold OS .21 XM Outboard $250

    Don Said mike gets it. Shame to not let him have it . He did it right and shouldn't be punished for it.
  3. Davidkrienke

    Sold OS .21 XM Outboard $250

    Just always talk on the main thread and not pm deals and the first I take it gets it and you will be fine. They can talk in pm about shipping per the rules after they say I will take it all you want after that as well.
  4. Davidkrienke

    Sold OS .21 XM Outboard $250

    Yeah but people ask all these same questions all the time then never follow through . That's why everyone sticks to the Ill take it being the final call on who gets it. If not there will be 5 tire kickers acting interested and no one ever says ill take it or will say decided to pass. Its just...
  5. Davidkrienke

    Sold OS .21 XM Outboard $250

    We have all seen this happen on here many times The I take it trumps all other questions. It should have been said I will take it How much will shipping be or I will take it and Pick it up at the race.
  6. Davidkrienke

    For Sale Eagle SGX 21 Hydro

    Read post 25 it is sold
  7. Davidkrienke

    Extreme left wokism in Kanuckistan.

    they also killed off Dilbert after all these years. Its a crazy world.
  8. Davidkrienke

    Outboard prop depth

    there is 3 pictures showing the prop setup on that manual and is confusing. The top two pictures would make you think it is really deep in the water . I would say the bottom picture near the tuning section is the correct way to have the height?
  9. Davidkrienke

    K&b 7.5 air leak issue

    you could remove it and when you install use some yamabond or hondabond smeared in the hole before you slide it in. or if you are up to it just some superglue medium thick and some baking soda dusted over and hit it with quick set only on the outside seam there. should soak in enough to seal and...
  10. Davidkrienke

    Push rod seals

    I also do this for throttle and switch pulls as well on some of my boats.you can use gold n rod or similar sheath and run small wire or cable with some grease on it to seal .This what you show would be best for how he has no room and needs to have a water tight seal .
  11. Davidkrienke

    A/A Pro 21 Update

    It would be easiest to just search for nova engines on youtube . Basically they are using just ok materials . Case has a plastic insert for carb that makes it hard to change bearings, crank is not slugged and the dlc coating is not very strong no slugs in cranks. and the cooling heads are coated...
  12. Davidkrienke

    Push rod seals

    With the zippkits small seal you can drill a hole then push grommet part through and use a small ring of brass tubing pushed inside the grommet to hold it in there tight. It works good.
  13. Davidkrienke

    A/A Pro 21 Update

    The more Videos I watch they just have lost all quality and are just a second rate company now. Such a shame to ruin a good name . They are cutting corners everywhere just to make a buck.
  14. Davidkrienke

    Sold K&B 11 cc + lowers

    In your picture the back of the engine pto looks to have a gap also. I wonder if something is hitting under the pto backplate not allowing the engine to come together with the lower unit. try pulling the flex shaft out and see if it goes together tight.
  15. Davidkrienke

    Stupd gas boat question..

    Also If you ever have a engine kick back on you it will yank your hand into the engine and also can put a nick in the boat as it slaps back down in the boat. We have had it happen a couple of times now. I wondered if the knot would help this. That was a good question you asked because I was...
  16. Davidkrienke

    Sold New CMB 21 Beta EVO

    Cmb Has a special going on engines that come with a upgraded cylinder and head for 473usd for the 21. That might be a better deal if the upgraded 12 port cylinder is better . Might be worth checking out.
  17. Davidkrienke

    Parts Wanted ROSSI Outboard Parts Needed

    You can get the piston/liner from high performance products I think still. My brother bought one a while back .
  18. Davidkrienke

    260pum starter pulley needed. Will this work?

    Ok that's great to hear. We might just go that route. Saves my brother from having to buy a starter. They do start easy once the low end it right but when its not Dang it will wear you out.
  19. Davidkrienke

    Sold OS Speed B2104 (huge discount)

    https://www.ebay.com/itm/224576930501?_trkparms=amclksrc%3DITM%26aid%3D777008%26algo%3DPERSONAL.TOPIC%26ao%3D1%26asc%3D20201018205123%26meid%3D079abb0dfd3a4d27a4c32f22d3fb7e74%26pid%3D101286%26rk%3D1%26rkt%3D1%26mehot%3Dnone%26itm%3D224576930501%26pmt%3D0%26noa%3D1%26pg%3D2380057%26algv%3DWatchli...
  20. Davidkrienke

    260pum starter pulley needed. Will this work?

    https://www.ebay.com/itm/144808174130?_trkparms=amclksrc%3DITM%26aid%3D1110013%26algo%3DHOMESPLICE.SIMRXI%26ao%3D1%26asc%3D246215%26meid%3Da44a31361cb14facb41c5cca40af7ec9%26pid%3D101196%26rk%3D5%26rkt%3D10%26sd%3D255147796732%26itm%3D144808174130%26pmt%3D1%26noa%3D0%26pg%3D2047675%26algv%3DPromo...
Back
Top