Search results

Intlwaters

Help Support Intlwaters:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. R

    Parts Wanted Looking for OPS and Picco engines/parts

    Update:: A machinery auction came up and I will be busy with moving some smaller but heavy machines for the next week.
  2. R

    Parts Wanted Looking for OPS and Picco engines/parts

    Update: it will be next week before I will be able to organize and post pics, probably Wednesday or later.
  3. R

    Parts Wanted Looking for OPS and Picco engines/parts

    I have a large drawer of Picco 67EXR engines and parts, a few new mostly used if you are interested I will catalog and take pics of the large collection. There might be some Picco EXR 80s in there.
  4. R

    Parts Wanted Floor Type Motor Mount

    Made by Victor Gorecki. He made a few, didnt sell well. I might still have one will check later today
  5. R

    Parts Wanted Wanted tune pipes

    Contact Alan Terry on Jim's RC Boat Dock, he has made many twin engine gas pipes and made them look great.
  6. R

    Parts For Sale I HAVE POSSIBLE ACCESS TO THE FOLLOWING PICCO SPARES NEW...

    I sold these and no longer have them, just posting for information.
  7. R

    Parts For Sale I HAVE POSSIBLE ACCESS TO THE FOLLOWING PICCO SPARES NEW...

    Here are some pics that contain part numbers of some of the parts I sold last year. These were most definitely 1999 Black head Long stroke EXR 7.5 engines with the larger front bearing 8mm ID.
  8. R

    Parts For Sale Cleaning out a hobby shop of K&B parts

    I got the file to download, but would not open.
  9. R

    Charging Li-fe Rx packs!

    I use mine to keep tabs on balancing both off charge and after use. Seen a few life receiver battery failures, all were from one cell going bad, could have been caught with a little more care.
  10. R

    Charging Li-fe Rx packs!

    A $10.00 battery balance voltage checker that plugs into the balance port helps keep tabs on each cell. A worthy addition to your pit box if using lithium batteries, life or lipo.
  11. R

    Paint removal!!

    If the paint is not "nitro proof", you could try 100% nitro to dissolve it and a small wire brush. But most people would only use an two part epoxy paint on the inside of a boat, so you may be out of luck on that.
  12. R

    Parts Wanted L/F OS Max EX- M Crankshaft

    Frank, the crank you are looking for is an inboard??? Could you post a picture of the crankcase??
  13. R

    Parts Wanted Looking for Kwik Stripe 1/8 gold

    Brad, I think you should get a tape like this from a current supplier of stripping tape. ( Do a Google search of "Striping tape for cars"). I got some tape in a box on the shelf but it is probably 20 to 40 years old. I would think a quality builder like you would want near new stuff and not...
  14. R

    2021 Christmas Giveaway starts now!

    Mark, I would like the 7F carb, please. Sending PM
  15. R

    Parts For Sale New OPS 45 rod

    This one looks like an early RPM rod, the early ones had a straight cut at the wrist pin end and parallel side cuts on the shank, later rods used more complicated CNC programming and had tapered shank and orbiting cuts around the wristpin and crank pin. So my vote is it is an early RPM rod.
  16. R

    1/8 scale cracker box cornering problems ?

    Pics of the bottom and pics of the strut setup would be very helpful.
  17. R

    New Nitro Engine

    Steel rod with needles or aluminum rod with bushes?? Or none of the above??
  18. R

    Parts Wanted OPS .67 Piston and Sleeve

    Please PM me if you want the rod!!
  19. R

    Parts Wanted OPS .67 Piston and Sleeve

    Picture for Chris Herzog. Notch in wrist pin hole.
  20. R

    Parts Wanted OPS .67 Piston and Sleeve

    Everything sold pending payment. PMs sent to all parties.
Back
Top