Sold K&B 11 cc + lowers

Joern Markset · Feb 18, 2023

K&B 7,5 cc lower, modified to fit 11 cc as well as use of tuned pipe. Clean lower in good shape.
$ 90,-
Shipping from $ 22,-
Paypal as FF

K&B 11 cc lower, new flex / teflon liner and new propshaft assy. Nice and clean lower.
$ 100,- SOLD
K&B 11 cc powerhead, good comp, bearings turn smooth (outer pto bearing could probably be replaced, but turns ok)
$ 50,- if purchased together with one of the above lower ends. SOLD

tommyLi · Feb 18, 2023

Hi , I need to K&B 11 cc lower, new flex & K&B 11 cc powerhead, good comp , Goods delivered USA Oregon 97080 how much shipping .

Joern Markset · Feb 18, 2023

tommyLi said:
Hi , I need to K&B 11 cc lower, new flex & K&B 11 cc powerhead, good comp , Goods delivered USA Oregon 97080 how much shipping .

Hi,
That will be 150 bucks for lower and powerhead, + 25 bucks shippingcost. If you want insured shipping it is 37 bucks.
Shipping on Monday morning if you decide to buy.

tommyLi · Feb 19, 2023

Hi , 150 bucks for lower and powerhead + insured transportation =180 Are you willing to accept , if you accept please give me Paypal .

Joern Markset · Feb 19, 2023

tommyLi said:
Hi , 150 bucks for lower and powerhead + insured transportation =180 Are you willing to accept , if you accept please give me Paypal .

Ok, I can do that.
You will need to send me your address, e-mail and a phone number you can be reached at. (it is for the shipping documents)
Send paypal to [email protected]
You will receive all necessary shipping info ones the documents have been made.
Thanks
Jørn

Edit: Payment received

tommyLi · Feb 19, 2023

Hi , Recipient to Chi Fai Li , 2893 sw 33RD ST Gresham Oregon USA 97080 , [email protected] , 15039157567 , I have sent to you Paypal account

Joern Markset · Feb 19, 2023

tommyLi said:
Hi , Recipient to Chi Fai Li , 2893 sw 33RD ST Gresham Oregon USA 97080 , [email protected] , 15039157567 , I have sent to you Paypal account

Document has been made up, a copy along with tracking info has been sent to your e-mail.
Thanks
Jørn

tommyLi · Feb 19, 2023

Thank

tommyLi · Feb 27, 2023

HI , The item has been received and is complete , but there is a problem , The connection between the exhaust port and the lower boby does not match , This can cause exhaust leaks , Yes rejected some parts .

Wasted wages · Feb 27, 2023

Missing the exhaust adaptor plate?

BobSmith1 · Feb 27, 2023

the adapter is there, sometimes there's a gap, I've seen where people put a small amount of high temp silicone, here's a new in box, less gap, but still a gap.

tommyLi · Feb 28, 2023

Wasted wages said:
Missing the exhaust adaptor plate?

This is what is not missing

tommyLi · Feb 28, 2023

BobSmith1 said:
the adapter is there, sometimes there's a gap, I've seen where people put a small amount of high temp silicone, here's a new in box, less gap, but still a gap.

Shim the crack

tommyLi · Feb 28, 2023

Thank for the guidance

Davidkrienke · Feb 28, 2023

tommyLi said:
Shim the crack

In your picture the back of the engine pto looks to have a gap also. I wonder if something is hitting under the pto backplate not allowing the engine to come together with the lower unit. try pulling the flex shaft out and see if it goes together tight.

tommyLi · Feb 28, 2023

There is a gap in the exhaust , and there is no problem with the rear connection

Joern Markset · Feb 28, 2023

I believe there is a gasket sitting on the pto as well, that can be peeled off.
Also make sure you get the pto completely and correct into the crankcasing when thightening up.
Still, as mentioned above, there is often gap to be seen here. You may cut some gasket material and shim out the exh adapter ring.
There is not missing parts.

tommyLi · Feb 28, 2023

The bottom part is flat

tommyLi · Feb 28, 2023

Joern Markset said:
I believe there is a gasket sitting on the pto as well, that can be peeled off.
Also make sure you get the pto completely and correct into the crankcasing when thightening up.
Still, as mentioned above, there is often gap to be seen here. You may cut some gasket material and shim out the exh adapter ring.
There is not missing parts.

Thank

Greg Rowe · Feb 28, 2023

I have had this same issue with 7.5 , 67,& 82
Not sure why but with the gap it will not run correctly, issues with pressure port to tank and loud as crap.
I suggest a garloc gasket material thick enough to apply pressure and not leak.
Just a thought

If you have bought, sold or gained information from our Classifieds, please donate to Int'l Waters and give back.

Sold K&B 11 cc + lowers

Help Support Intlwaters:

Well-Known Member

Attachments

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Attachments

Well-Known Member

Attachments

Well-Known Member

Attachments

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Attachments

Well-Known Member

Well-Known Member

Attachments

Well-Known Member

Well-Known Member

Similar threads

Join the conversation!

Join today and get all the highlights of this community direct to your inbox. It's FREE!