Parts Wanted Parts Wanted 15cc K90 carb

Tom Bush · Jan 16, 2023

Hi guys looking for two of these . If u got one or two pm me please .thx

looking for 2 of these. I think they are K90 nitro carbs . I like to find new, if possible .
i have other new carbs to trade for 15cc motors.

brad nichols · Jan 16, 2023

Good luck, you could try Al Hobbs

Brad

Tom Bush · Jan 16, 2023

Can’t find Al Hobbs

AgafonovRoman · Jan 17, 2023

This can be addressed to Frank Werner from Germany. You can find him here on IW. He can have it.

Wasted wages · Jan 17, 2023

Tom Bush said:
Hi guys looking for two of these . If u got one or two pm me please .thx View attachment 312699

i have other new carbs to trade for 15cc motors.

What other carbs do you have to trade ?
Any pictures?

brad nichols · Jan 17, 2023

Al's email [email protected]

NITROSNIFER · Jan 17, 2023

PM me

Al Hobbs · Jan 17, 2023

brad nichols said:
Al's email [email protected]

That is not my email. [email protected] is the correct email.

brad nichols · Jan 18, 2023

Sorry Al it was the last one I had

Brad

Jeff Lutz · Feb 20, 2023

Tom Bush said:
Hi guys looking for two of these . If u got one or two pm me please .thx View attachment 312699

looking for 2 of these. I think they are K90 nitro carbs . I like to find new, if possible .
i have other new carbs to trade for 15cc motors.

I have this one I will sell for $70 shipped. Its a version before yours with a different velocity stack.

Tom Bush · Feb 26, 2023

Thx Jeff but that does not help me . I actually have a few of those but I am looking for two with the molded in velocity stacks on them.

Jeff Lutz · Feb 26, 2023

Tom Bush said:
Thx Jeff but that does not help me . I actually have a few of those but I am looking for two with the molded in velocity stacks on them.

I tested the one you like also. I have those but need to keep them in case I sell my K90’s. You can fit Mac .67/.84 carbs easily to a K 90 and they run better. You could have Speedmaster make you some also. I ran 119 mph with .510“ carbs with twin K90’s many years ago. With the long intake on those engines I prefer short bell carbs.

Tom Bush · Mar 8, 2023

This is the motor I am looking for carbs for .

Tom Bush · Mar 8, 2023

This is the motor I am looking for carbs for .

Tom Bush · Mar 8, 2023

The carbs on the motor on the pic do not have a needle . does that mean you must use a remote needle? I reall do not want to use remotes as I an trying to keep the look as a real v6 motor.
good low idle is what I want .

Mike Hughes · Mar 8, 2023

You gonna need remote needles with those carbs. Now that I think about it, I am not sure there is a carb that size with an needle. Most are remote.
Mike

Zimmerman · Mar 9, 2023

I have 2 of the carbs you might be looking for. One is stock, the other has been machined off. $160 + the ride if they will help you.
Rich

Tom Bush · Mar 11, 2023

I have some of these carbs. Very unique setup. The barrel slides in and out. With this is the needle that slides in and out with the barrel giving you total adjustments in fuel flow with air flow. This will probably be the best for low idle. the side barrel sticks out and it interferes and hits the motor intake. But I can have some alum cyclinders made to raise the carbs just enough to fit and use extra long screws. i just don’t like the looks but I might have to get over that. Hear some pic ,has anyone use these carbs?

If you have bought, sold or gained information from our Classifieds, please donate to Int'l Waters and give back.

Parts Wanted Parts Wanted 15cc K90 carb

Help Support Intlwaters:

Member

Well-Known Member

Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Legend of the NW

Well-Known Member

Well-Known Member

Attachments

Member

Well-Known Member

Member

Attachments

Member

Member

Well-Known Member

Well-Known Member

Attachments

Member

Attachments

Similar threads

Join the conversation!

Join today and get all the highlights of this community direct to your inbox. It's FREE!