Jump to content

1olddog

Members
  • Content Count

    22
  • Joined

  • Last visited

Everything posted by 1olddog

  1. 1olddog

    K&B 3.5 Outboard Set Screw

    Anybody know what size allen wrench the set screw on the drive dog on a K&B 3.5 cc outboard takes ? I looked on Mecoa's site but found no info about it.
  2. 1olddog

    K&B 3.5 Outboard Set Screw

    Thanks everyone for the replies. I sold a K&B 3.5 cut for an electric conversion to a guy and gave him this prop shaft assembly in case he wants to try to fix it.
  3. 1olddog

    K&B 3.5 Outboard Set Screw

    I didn't have a small enough punch so I used a small allen wrench and tapped it out. The unit had a lot of wobble in it and I thought I might be able to put a brass sleeve in it to take the wobble out.This little prop shaft assemblies are costly so I thought I might be able to rebuild it.
  4. 1olddog

    K&B 3.5 Lower

    Price lowered to $40 + shipping
  5. 1olddog

    K&B 3.5 Lower

    SOLD.....Polished K&B 3.5 lower unit with new stainless steel screws,teflon tube and flexshaft.Also comes with prop shaft,bullet prop nut, transom mount and water pickup tube. Will need water line to the pickup.Has some marks on other side from cutting off long screws,that doesn't affect operation. Speckles aren't on unit,just in pic.Price is $40 + shipping. Will ship worldwide
  6. 1olddog

    Calling it quits

    Bob, I found one,but thanks for your help.
  7. 1olddog

    Calling it quits

    As little as possible.I have to bore out where the prop shaft enters and exits the lower to accept a 3/16" or 1/4" prop shaft. May mess it up so something that's not good ,but all there. Maybe around $20
  8. 1olddog

    Calling it quits

    Bob, do you have a used K&B 7.5 lower cheap without the internal parts ? Just using it for a project,so it doesn't need to be pretty.I called you once about it ,but couldn't understand our conversation,because you were outside in windy conditions.Below is what I want to do with it. Trying to make a steerable outdrive like the one pictured for a big hull I have.
  9. FOUND Looking for a set of instructions on how to attach the cover to a K&B 3.5cc lower unit.I'll be using an electric motor instead of a K&b 3.5cc.
  10. 1olddog

    DPI Outboard Cover Instructions

    Got instructions from another member on RC Groups.
  11. 1olddog

    Outboard Skeg

    Would one of these work ?Just cut off the skeg. http://hyperprod.bizhosting.com/3_5_angle_drive.html
  12. 1olddog

    Class C Racing Runabout

    Does anyone have the plans for it that they might want to sell or make a copy of at my expense ? It was in the Sept 2004 issue of RCM magazine.It was a yellow boat with a K&b 3.5 outboard on it.The plans were by Bob Stark.RCM is no longer with us,so this is the only way to get plans.I have the build article that has the plans in it ,but coping them or putting them on a disk hasn't worked. Racing Runabout Build Article.zip
  13. 1olddog

    Class C Racing Runabout

    I might just try that if I can find a projector. Would I have to trace the plans first or see if the ones from the build article that I printed enlarge and come out clear enough ?
  14. 1olddog

    What Is It

    I've been told this is to hold a nitro fuel tank in an r/c boat,but I'm not sure.I build and run gassers,so this is foreign to me.It's made of plywood and is coated and fits between 5" rails.It was in a box of stuff I bought from an r/c store that went out of business.I've been trying to give it away on other sites,with the person taking it paying the postage,but no takers yet.Thought maybe I've been advertising it as something it's not.
  15. 1olddog

    42" Predator

    This is one of about 40 of these fiberglass hulls that Vern Kilmer (Forabuck) made for electric or nitro power.It is 42" long x 13" wide and has rails installed at 5 " and weighs 7lb 5 oz empty.It has never been built and has no holes in the bottom or transom and the deck isn't attached to the bottom.I will supply a tube of 3M 5200 for you to do it.I installed round vents in the rear deck to let heat out.It is a beautiful purple metal flake gelcoat finish. I was going to put a Zen 260 gasoline engine in it ,but lost interest.Price is $125 + shipping
  16. 1olddog

    42" Predator

    Price is reduced to $100 + shipping
  17. 1olddog

    FS Prather Props

    I have 2 Prather 250 props,3/16" bore,new never used,but the guy I got them from in a boat deal started to sharpen one of the blades on one prop.Price is $12.50 each shipped in US
  18. 1olddog

    Dumas Scarab 38 KV 55" Nitro

    I thought I 'd offer this for sale again before I start stripping the paint off of it .It has all hardware,fuel tank,lines,side hull fuel filler,dual underhull water pickups,electric pump to supply water to engine at low speed,antenna.Needs touched up or repainted.Price $250.00 shipped without engine or $400.00 shipped with the OS77 VR-M,with tuned pipe in US (lower 48)only.Pay by Paypal( no fees) or US postal money order.Email zenoah2005@msn.com for pics
  19. 1olddog

    Dumas Scarab 38 KV 55" Nitro

    This boat is ARR with an OS77VR-M with tuned pipe and has running hardware,fuel tank and lines,water lines,electric water pump to supply water at low speed and siphon water out of hull.Has dual water pickups under hull ,fuel filler,water outlets,antenna,older servos and receiver.Good condition with a few paint chips,no radio.Will sell with engine for $450.00 or without it for $250.00 + shipping.Accept Paypal or US postal money order only.Email zenoah2005@msn.com for pics
  20. 1olddog

    Dumas Scarab 38 KV 55"

    Dumas Scarab 55''long and has all running hardware,fuel tank,lines,dual water pickups under hull,fuel filler valve in side of hull,and electric pump to supply engine with water on low speed and to siphon water from hull.Will sell without OS .77VR-M race engine for $250.00 or with it for $450.00 + shipping.Good condition with a few paint chips.Can be set up for gas engine by putting in 5" engine rails.Accept Paypal or US postal money order.Email: zenoah2005@msn.com for pics
  21. 1olddog

    Dumas Dauntless ARR

    Electric powered 49 1/2" with two Astro 25"s.Comes with Astro ESC,servos,props.Just add batteries,either cell packs or 12 volt motorcycle battery and your radio gear.Good condition,but has a few paint chips.Price $250.00+ shipping in US only.Payment by Paypal or US Postal money order.
  22. 1olddog

    Dumas Scarab 38 KV 55"

    Boat is setup for nitro,but can be converted to gas or electric.Comes with hardware,prop,fuel tank,servos,receiver,side hull fuel filler and water outlets.Has dual water pickups under hull and an electric pump to supply water to engine at low speed and also siphons water out of hull.Good shape with a few paint chips.Price $275.00+ shipping in US only.Paypal and US Postal money orders
×